Panasonic PT-RZ31K / PT-RS30K (serv.man2) Service Manual ▷ View online
ADJ-7
SECTION 3 ADJUSTMENTS
<RZ31K/RS30K>
1. 3. EEPROM data transfer
1. 3. 1. Equipment to be used
1. Computer : Use it for the transfer of backup data.
2. Communication cable :
Serial terminal connection D-sub 9pin (male/female RS-232C straight)
LAN terminal connection LAN cable (When connecting directly, use a cross cable)
3. Service Software : [DataLogBackup.exe] Download from the projector service Web (PASS).
1. 3. 2. Connection Preparations
1. Check the settings of the projector
Serial terminal connection
1) The [INPUT SELECT] of sub menu [RS-232C] must be set according to the connection method.
2) Check the RS-232C settings (ID, Baudrate and Parity) and take a note.
LAN terminal connection
1) The [DIGITAL LINK MODE] of sub menu [NETWORK], please select to [AUTO] or [ETHERNET].
2) Check the network IP address of the projector and take a note.
3) Set the IP address of computer to approximate value of projector IP address.
[Note] • If you have changed the each menu settings, please return settings of the original (customers) after work.
2. Connect the projector and the PC by using a communication cable.
Serial terminal connection
Computer
Projector
Serial cable (RS-232C)
SERIAL IN
LAN terminal connection
Computer
Projector
LAN cable (straight)
LAN cable (straight)
LAN
1. 3. 3. Backup the EEPROM data (It is before circuit board exchange)
1. Switch the projector to "Normal-Standby" mode (STANDBY/ON indicator is lighting in red).
2. Service software to run with a computer.
2. Service software to run with a computer.
ADJ-8
SECTION 3 ADJUSTMENTS
<RZ31K/RS30K>
3. Select [Setting] of [Option] menu, then select connection method and enter the setting information of the projector.
items
Default value
SERIAL
Port
–
Baud Rate
9600bps
Parity
None
LAN
IP Address
192.168.0.8
Username
admin1
Password
panasonic
Command Port
1024
Serial terminal connection
• Select [SERIAL] menu and set up the Serial Port, Baudrate and Parity of the PC
LAN terminal connection
• Select [LAN] menu and set up the IP address, Username, Password and Command Port of the projector.
[Note] • If the Username and Password has been changed, please select serial terminal connection
4. Select a model number and ID.
ADJ-9
SECTION 3 ADJUSTMENTS
<RZ31K/RS30K>
5. Select the "Backup (EEPROM)” tab and put a checkmark to the "REPLACE A-PWB" of "COPY MODE" item.
Then click the [READ EEPROM] button.
l
k
j
6. Select the save place and click [Save(S)] button.
7. Once the progress bar reaches the right side end, it is a read completion of the data.
• [WRITE EEPROM] button and [READ EEPROM] button will return to normal display from gray.
8. Select the "Quit" of "File" menu and quit the software.
ADJ-10
SECTION 3 ADJUSTMENTS
<RZ31K/RS30K>
1. 3. 4. Restore the backup EEPROM data (After circuit board replace)
1. Switch the projector to "Normal-Standby" mode (STANDBY/ON indicator is lighting in red).
2. Start up service software [DataLogBackup.exe] with a computer.
3. Select [Setting] of [Option] menu, then select connection method and enter the setting information of the projector.
4. Select a model number and ID.
5. Select the "Backup (EEPROM)” tab and put a checkmark to the "REPLACE A-PWB" of "COPY MODE" item.
Then click the [WRITE EEPROM] button.
l
k
j
6. Select the saved file and click [OPEN(O)] button.
7. Once the progress bar reaches the right side end, it is a write completion of the data.
• [WRITE EEPROM] button and [READ EEPROM] button will return to normal display from gray.
8. Select the "Quit" of "File" menu and quit the software.
9. Restart the main power of projector and check that it operates properly.
Click on the first or last page to see other PT-RZ31K / PT-RS30K (serv.man2) service manuals if exist.