Panasonic PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) Service Manual ▷ View online
DIS-15
SECTION 2 DISASSEMBLY PROCEDURE
<MZ16K/MZ13K/MZ10K>
F
F
G
H
D
D
D
E
2.9.3. Power intake fan removal
1. Remove 3 screws-D and 1 screw-E and take the Power intake fan off.
2. Remove 2 screws-F and take the V-PCB off. Remove 1 screw-G and take the
R-PCB off. Remove 1 screw-H and take the RM-PCB off.
D
E
F, G
H
J
K
L, M
N
Power intake fan
(POWER INTAKE)
V-PCB
R-PCB
RM-PCB
M
N
L
J
K
K
K
2.9.4. Power exhaust fan removal
1. Remove 3 screws-J, 1 screw-K and take the Power exhaust fan off.
2. Remove 1 screw-L and take the RF-PCB off. Remove 1 screw-M and take the
M2-PCB off. Remove 1 screw-N and take the RG-PCB off.
R-PCB
RF-PCB
CN1-PCB
Power exhaust
fan(EXHAUST2)
RG-PCB
M2-PCB
DIS-16
SECTION 2 DISASSEMBLY PROCEDURE
<MZ16K/MZ13K/MZ10K>
P
P
P
P
P
2.9.5. P-PCB removal
1. Remove 5 screws-P and take the P-PCB off.
P-PCB
P
2.10. Lighting case block removal
1. Remove 1 screw-A and take the Lens dust cover off.
2. Remove 4 screws-B, 1 screw-C and the remove the Tank of liquid cooling unit from the cover. and then take
the lens cover bottom off.
3. Remove 4 screws-D, 3 screws-E and take the Lighting case block upward off.
B
A
B
B
C
D
D
D
D
E
E
E
Lighting case block
Lens dust cover
Lens cover bottom
A
C
E
B
C
D
DIS-17
SECTION 2 DISASSEMBLY PROCEDURE
<MZ16K/MZ13K/MZ10K>
G
F
F
F
F
2.10.1. Lens mounter removal
1. Remove 4 screws-F and take the lens mounter block off from the Lighting case .
2. Remove 2 screws-G and take the LM-PCB off.
Lens mounter block
Lighting case
LM-PCB
F
G
2.10.2. Optical block removal
1. Loosen 4 hex screws-H and take the Optical block off from the Lems mounter.
H
Lens mounter unit
Optical block
H
DIS-18
SECTION 2 DISASSEMBLY PROCEDURE
<MZ16K/MZ13K/MZ10K>
2.11. Filter case removal
1. Remove 10 screws-A and take the Filter case upward off.
2. Remove 1 screw-B and take the F-PCB off.
A
B
C
A
B
A
A
A
B
C
A
A
A
B
A
A
Filter case
F-PCB
2.12. Intake duct top, PBS fan removal
1. Take the PBS fan upward off.
2. Remove 3 screws-A and take the Intake duct top off.
3. Remove 1 screw-B and take the Intake duct top sponge off.
4. Remove 1 screw-C and take the M3-PCB off.
PBS fan
M3-PCB
Intake duct top
Intake duct top sponge
Note on mounting of PBS fan
After replaceing the PBS fan, mount the sponge
onto the 3 screw holes as shown in the figure, and
place them to the intake duct top.
* Use sponges with new one at the time of replacing
the fan.
Turn the sponge as
the arrow.
Sponges
Click on the first or last page to see other PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) service manuals if exist.