Panasonic PT-JX200HBU / PT-JX200HWU / PT-JX200GBE / PT-JX200GWE / PT-JX200GBD / PT-JX200GWD (serv.man2) Service Manual ▷ View online
6
PREFACE
< JX200 >
1. Safety Precautions
1. 1. General Guidelines
- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed
and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged
by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combi-
nations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.
1. 2. Leakage Current Check
1. Prepare the measuring circuit as shown in Fig.1.
Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer
because of a possibility of an electric shock.
M1
M2
Rs
Cs
Rb
10KΩ ±0.1%
0.022µF
±1.0%
Vb
(V) V
Rs: 1500 Ω±0.1%
Cs: 0.22 µF±1.0%
Rb: 500 Ω±0.1%
to T1
or T2
in FIg.2
Weighted leakage current=Vb / 500 (A)
Fig. 1
Isolation transformer
T1
T2
connection
to power outlet
M1
M2
Fig.2
Projector
Measuring
Circuit (Fig.1)
Performance
Voltmeter
(rms reading)
Accurancy:
≤ 2%
Input resistance:
≥ 1 MΩ
Input capacitance: ≤ 200 pF
Frequency range: 15 Hz to 1 MHz
Table. 1
7
PREFACE
< JX200 >
2. Specifications
2. 1. Specifications
The specifications of the projector are as follows.
▪PT-JX200HBU/JX200HWU
Model No.
PT-JX200HBU/PT-JX200HWU
Power supply
120 V ~ (120 V alternating current), 50 Hz/60 Hz
Power consumption
240 W (2.3 A)
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.4 W
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.4 W
*1
In standby mode (when [STANDBY MODE] is set to [NETWORK]): 0.5 W
*2
In standby mode (when [STANDBY MODE] is set to [NORMAL] and the fans are stopping): 12 W
DLP chip
Size
14.0 mm (0.55") (aspect ratio 4:3)
Display system
1-unit DLP chip, DLP type
Number of pixels 786 432 pixels (1 024 x 768 dots)
Lens
Electric zoom
1.3 to 2.9:1
Electric focus
F = 2.0 to 2.7
f = 15.2 mm to 32.7 mm
Light source
Laser diode (Maximum output: 36 W x 2, Wavelength: 452 - 458 nm)
Light output
*3
2 000 lm (ANSI)
Contrast ratio
*3
1 000:1
Projected image size
0.76 m (30") to 5.08 m (200")
Screen aspect ratio
4:3
Projection method
[FRONT]/[REAR]
(On/off of vertical flip can be set with [VERTICAL FLIP])
Card slot
SD card slot
*4
x 1 (supports SDHC memory card)
Outer case
Molded plastic
Outer color
PT-JX200HBU: Black, PT-JX200HWU: White
Weight
4.5 k] (9.92 lbs.)
Noise level
*3
When [LIGHT POWER] is set to [NORMAL]: 33 dB
When [LIGHT POWER] is set to [ECO]: 30 dB
Operating
environment
Temperature
*5
0 °C (32 °F) to 40 °C (104 °F)
Humidity
10 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (AAA/R03 or AAA/LR03 battery x 2)
Operating range Within approx. 7 m (22'11") (when operated directly in front of signal receiver)
Weight
Weight
63 ] (2.2 ozs.) (including batteries)
Dimensions
Width: 44 mm (1-23/32"), Height: 105 mm (4-1/8"), Depth: 20.5 mm (13/16")
*1 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], the network function (both wireless LAN and wired LAN)
cannot be used in standby mode.
*2 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NETWORK], the network function while in standby mode is
restricted to the projector operations via wired LAN using the Wake on LAN function.
*3 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*4 Operations of the Panasonic SD memory card up to capacity of 2 GB and Panasonic SDHC memory card up to capacity of 32 GB are confirmed.
*5 The operating environment temperature should be between 0 °C (32 °F) and 35 °C (95 °F) when using the projector at elevations between 1 000 m
(3 281') and 2 700 m (8 858') above sea level.
8
PREFACE
< JX200 >
▪PT-JX200GBE/JX200GWE, PT-JX200GBD/JX200GWD
Model No.
PT-JX200GBE/PT-JX200GWE, PT-JX200GBD/PT-JX200GWD
Power supply
100 V - 240 V ~ (100 V - 240 V alternating current), 50 Hz/60 Hz
Power consumption
240 W (2.7 A - 1.1 A)
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.5 W
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.5 W
*1
In standby mode (when [STANDBY MODE] is set to [NETWORK]): 0.7 W
*2
In standby mode (when [STANDBY MODE] is set to [NORMAL] and the fans are stopping): 12 W
DLP chip
Size
14.0 mm (0.55") (aspect ratio 4:3)
Display system
1-unit DLP chip, DLP type
Number of pixels 786 432 pixels (1 024 x 768 dots)
Lens
Electric zoom
1.3 to 2.9:1
Electric focus
F = 2.0 to 2.7
f = 15.2 mm to 32.7 mm
Light source
Laser diode (Maximum output: 36 W x 2, Wavelength: 452 - 458 nm)
Light output
*3
2 000 lm (ANSI)
Contrast ratio
*3
1 000:1
Projected image size
0.76 m (30") to 5.08 m (200")
Screen aspect ratio
4:3
Projection method
[FRONT]/[REAR]
(On/off of vertical flip can be set with [VERTICAL FLIP])
Card slot
SD card slot
*4
x 1 (supports SDHC memory card)
Outer case
Molded plastic
Outer color
PT-JX200GBE: Black, PT-JX200GWE: White
Weight
4.5 k] (9.92 lbs.)
Noise level
*3
When [LIGHT POWER] is set to [NORMAL]: 33 dB
When [LIGHT POWER] is set to [ECO]: 30 dB
Operating
environment
Temperature
*5
0 °C (32 °F) to 40 °C (104 °F)
Humidity
10 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (AAA/R03 or AAA/LR03 battery x 2)
Operating range Within approx. 7 m (22'11") (when operated directly in front of signal receiver)
Weight
Weight
63 ] (2.2 ozs.) (including batteries)
Dimensions
Width: 44 mm (1-23/32"), Height: 105 mm (4-1/8"), Depth: 20.5 mm (13/16")
*1 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], the network function (both wireless LAN and wired LAN)
cannot be used in standby mode.
*2 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NETWORK], the network function while in standby mode is
restricted to the projector operations via wired LAN using the Wake on LAN function.
*3 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*4 Operations of the Panasonic SD memory card up to capacity of 2 GB and Panasonic SDHC memory card up to capacity of 32 GB are confirmed.
*5 The operating environment temperature should be between 0 °C (32 °F) and 35 °C (95 °F) when using the projector at elevations between 1 000 m
(3 281') and 2 700 m (8 858') above sea level.
9
PREFACE
< JX200 >
2. 2 Applicable scanning frequency/terminal/wireless LAN
▪PT-JX200HBU/JX200HWU
Model No.
PT-JX200HBU/PT-JX200HWU
Applicable
scanning
frequency
*1
HDMI signal
525 (480) /60p, 525 (480) /60i, 625 (576) /50p, 625 (576) /50i, 750 (720) /60p, 750 (720) /50p,
1125 (1080) /60p, 1125 (1080) /60i, 1125 (1080) /50p, 1125 (1080) /50i
640 x 480/60, 800 x 600/56, 800 x 600/60, 1024 x 768/60, 1280 x 1024/60,
640 x 480/60, 800 x 600/56, 800 x 600/60, 1024 x 768/60, 1280 x 1024/60,
1280 x 720/50, 1280 x 720/60, 1280 x 768/50, 1280 x 768/60,
1280 x 800/50, 1280 x 800/60, 1600 x 900/50, 1600 x 900/60
Terminal
<HDMI IN>
terminal
1 set, HDMI 19 pins, HDCP compatible
Audio signal: Linear PCM (Sampling frequency: 48 kHz/44.1 kHz/32 kHz)
<AUDIO OUT>
terminal
1 set, M3 stereo mini jack (monitor output, stereo compatible)
0 V [rms] to 2.0 V [rms] (variable), output impedance 2.2 kΩ or less
<LAN> terminal
1 set, RJ-45, for network connection, PJLink compatible, 10Base-T/100Base-TX
<DC OUT>
terminal
USB connector (type A) x 1, for power supply (DC 5 V, maximum 2 A)
Wireless
LAN
Compliance
standards
MIRRORING
mode
IEEE802.11b/g/n: 2.412 GHz - 2.462 GHz
IEEE802.11a/n: 5.180 GHz - 5.240 GHz
5.745 GHz - 5.805 GHz
M-DIRECT mode
IEEE802.11b/g/n: 2.412 GHz - 2.462 GHz
IEEE802.11a/n: 5.180 GHz - 5.240 GHz
5.745 GHz - 5.825 GHz
USER mode
IEEE802.11b/g/n: 2.412 GHz - 2.462 GHz
IEEE802.11a/n: 5.180 GHz - 5.240 GHz
5.260 GHz - 5.320 GHz
5.500 GHz - 5.700 GHz (except 5.600 GHz - 5.650 GHz)
5.745 GHz - 5.825 GHz
Modulation
DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM, MIMO
Transmission
speed
IEEE802.11b: Up to 11 Mbps
IEEE802.11g/a: Up to 54 Mbps
IEEE802.11n: Up to 300 Mbps
Wireless channel
MIRRORING
mode
IEEE802.11b/g/n: 1~11 channel
IEEE802.11a/n: 36 / 40 / 44 / 48 channel
149 / 153 / 157 / 161 channel
M-DIRECT mode
IEEE802.11b/g/n: 1~11 channel
IEEE802.11a/n: 36 / 40 / 44 / 48 channel
149 / 153 / 157 / 161 / 165 channel
USER mode
IEEE802.11b/g/n: 1~11 channel (Active scanning)
IEEE802.11a/n: 36 / 40 / 44 / 48 channel (Active scanning)
52 / 56 / 60 / 64 channel (Passive scanning)
100 / 104 / 108 / 112 / 116 / 132 / 136 / 140 channel (Passive scanning)
149 / 153 / 157 / 161 / 165 channel (Active scanning)
Communication
distance
Approx. 30 m (98'5") (depends on the usage environment)
Security
Infrastructure mode
WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES), WEP (128 bit/64 bit),
WPA-EAP/WPA2-EAP (PEAP [MS-CHAPv2/GTC], EAP-FAST [MS-CHAPv2/GTC],
EAP-TTLS [MD5/MS-CHAPv2])
*1 Refer to Operating Instructions “List of compatible signals” for details of the types of video signals that can be used with the projector.
Note
f
The model numbers of accessories, etc. are subject to change without prior notice.
Click on the first or last page to see other PT-JX200HBU / PT-JX200HWU / PT-JX200GBE / PT-JX200GWE / PT-JX200GBD / PT-JX200GWD (serv.man2) service manuals if exist.