Panasonic PT-EX12KU / PT-EX12KE Service Manual ▷ View online
-17-
Maintenance
4) Attach the air filter.
• Insert the air filter with its tabs facing down.
• Insert the air filter with its tabs facing down.
5) Slide the air filter cover to the original position.
• Perform Step 1) in the reverse order.
• Perform Step 1) in the reverse order.
6) Reset the filter counter.
• Turn on the power and perform [Filter counter reset] in the [Setting] menu.
• Turn on the power and perform [Filter counter reset] in the [Setting] menu.
Attention
• After washing the air filter, dry it thoroughly before attaching to the projector. Attaching wet air filter may cause
• After washing the air filter, dry it thoroughly before attaching to the projector. Attaching wet air filter may cause
electric shock or malfunction.
Note
• Be sure to attach the air filter properly. If you use the projector without attaching the air filter, the projector may
• Be sure to attach the air filter properly. If you use the projector without attaching the air filter, the projector may
be damaged due to the dirt or dust.
• If the air filter has been damaged or dirt remains even after washing it, replace it with a a new filter.
• It is recommended that the air filter is replaced after two times of cleaning and reusing.
• After washing, the capability of the air filter may decrease.
• After washing the air filter, reset the filter counter. Otherwise, the power of the projector may be turned off for-
• It is recommended that the air filter is replaced after two times of cleaning and reusing.
• After washing, the capability of the air filter may decrease.
• After washing the air filter, reset the filter counter. Otherwise, the power of the projector may be turned off for-
safety.
-18-
Maintenance
Replacing the unit
The replacement filter is optional. To purchase the product, consult your dealer.
Replacement air filter : ET-RFE12
n
Replacement of the air filter
1) Slide the air filter cover.
• Pull and slide the air filter cover in the direction shown by the arrow.
• The top part of the air filter appears.
• Pull and slide the air filter cover in the direction shown by the arrow.
• The top part of the air filter appears.
2) Remove the air filter.
• Hold the grip of the air filter to pull up.
• Hold the grip of the air filter to pull up.
3) Attach the new air filter.
• Insert a new air filter with its tabs facing down.
• Insert a new air filter with its tabs facing down.
4) Slide the air filter cover to the original position.
• Perform Step 1) in the reverse order.
• Perform Step 1) in the reverse order.
5) Reset the filter counter.
• Turn on the power and perform [Filter counter reset] in the [Setting] menu.
• Turn on the power and perform [Filter counter reset] in the [Setting] menu.
Attention
• Make sure to turn off the power before replacing the air filter.
• When attaching the unit, make sure that the projector is stable. Perform the replacement in a safe place where
• Make sure to turn off the power before replacing the air filter.
• When attaching the unit, make sure that the projector is stable. Perform the replacement in a safe place where
the projector will not be damaged even if you drop the air filter.
• When turning the projector on, make sure that the air filter is installed before using the projector. Failure to do
so may cause damage.
• After replacing the air filter, reset the filter counter. Otherwise, the power of the projector may be turned off
forsafety.
Air filter unit
-19-
Maintenance
Lamp unit
The lamp unit is a consumable component. Check the lamp usage duration with “[Information] menu” and perform
regular replacement.
If the replacement message is displayed on the screen and the lamp indicators <LAMP 1 REPLACE>/<LAMP 2
REPLACE> turn on, replace the lamp units.
regular replacement.
If the replacement message is displayed on the screen and the lamp indicators <LAMP 1 REPLACE>/<LAMP 2
REPLACE> turn on, replace the lamp units.
Replacement lamp : ET-LAE12
Attention
• Do not replace the lamp unit until it has cooled down sufficiently. (Wait at least 60 minutes after use.) The inside
• Do not replace the lamp unit until it has cooled down sufficiently. (Wait at least 60 minutes after use.) The inside
of the cover is very hot and may cause burns.
n
Notes on the replacement of the lamp unit
The lamp unit is a consumable component. Replace the lamp unit regularly, as its brightness gradually decreases
over time. The estimated duration before replacement is 2 000 hours (when [Lamp power] is set to standard).
However, this may be shortened depending on individual lamp characteristics, usage conditions, and the installa-
tion environment. Earlier replacement of lamp units is recommended for this reason.
The duration exceeds 2 200 hours of usage for one lamp, the lamp will be switched to the other one if it is avail-
able.
If the power is turned on without replacing the lamps after the duration exceeds 2 200 hours of usage for all lamps,
the power automatically turns off after approximately ten minutes to prevent the malfunction of the projector.
over time. The estimated duration before replacement is 2 000 hours (when [Lamp power] is set to standard).
However, this may be shortened depending on individual lamp characteristics, usage conditions, and the installa-
tion environment. Earlier replacement of lamp units is recommended for this reason.
The duration exceeds 2 200 hours of usage for one lamp, the lamp will be switched to the other one if it is avail-
able.
If the power is turned on without replacing the lamps after the duration exceeds 2 200 hours of usage for all lamps,
the power automatically turns off after approximately ten minutes to prevent the malfunction of the projector.
• Since the luminous lamp is made of glass, it may burst if dropped or hit with a hard object. Please handle with
care.
• A Phillips screwdriver is necessary when replacing the lamp unit.
• When replacing the lamp unit, be sure to hold it by the handle.
• To prevent glass fragments from scattering, hold the lamp unit vertically when replacing it. When the projector
• When replacing the lamp unit, be sure to hold it by the handle.
• To prevent glass fragments from scattering, hold the lamp unit vertically when replacing it. When the projector
is attached to the ceiling, do not work directly under the lamp cover or put your face near it. Remove the lamp
cover slowly.
cover slowly.
• The lamp contains mercury. When disposing of the used lamp unit, ask your nearest local authorities or dealer
about proper disposal of the unit.
Attention
• Use only specified lamp units.
• The product numbers of accessories and separately sold components are subject to change without notice.
• Replacement of all two lamps simultaneously is recommended to ensure a balance brightness and tint.
• Use only specified lamp units.
• The product numbers of accessories and separately sold components are subject to change without notice.
• Replacement of all two lamps simultaneously is recommended to ensure a balance brightness and tint.
On-screen display
Lamp indicator
<LAMP 1 REPLACE>/<LAMP 1 REPLACE>
The lamp replacement instructions notify the replace-
ment time, and the lamp status notifies which lamp to
replace.
ment time, and the lamp status notifies which lamp to
replace.
Turns orange.
n
When to replace the lamp unit
-20-
Maintenance
Attention
• Turn off the UV lamp before opening the lamp cover.
• When the projector is mounted on the ceiling, do not put your face near the lamp unit.
• Attach the lamp unit securely.
• If the lamp unit is not attached properly, remove it and then attach it again. Forcing the lamp unit in may break
• Turn off the UV lamp before opening the lamp cover.
• When the projector is mounted on the ceiling, do not put your face near the lamp unit.
• Attach the lamp unit securely.
• If the lamp unit is not attached properly, remove it and then attach it again. Forcing the lamp unit in may break
the connector.
• The glass surface may be hot. When replacing the lamp unit, be sure to hold it by the handle.
1) Check which lamp to replace with the lamp status displayed on the screen, or the lamp indicators
<LAMP 1 REPLACE> / <LAMP 2 REPLACE>.
2) Turn off the power and disconnect the power plug from the power outlet, and wait at least 60 minutes,
and then check if the lamp unit has cooled down.
3) Use a Phillips screwdriver to turn the lamp cover fixing screw until they turn freely, and then open the
lamp cover.
• Pull the lamp cover in the direction of arrow (i) and lift it up in the direction of arrow (ii) to open.
n
Replacing the lamp unit
(i)
(i)
(ii)
(i)
(i)
(ii)
Screw
Lamp cover
Click on the first or last page to see other PT-EX12KU / PT-EX12KE service manuals if exist.