PT-DZ16KU, PT-DZ16KE, PT-DS16KD (serv.man11) — Panasonic Projector Other Service Manuals (repair manual)

Model
PT-DZ16KU PT-DZ16KE PT-DS16KD (serv.man11)
Pages
14
Size
524.13 KB
Type
PDF
Document
Other Service Manuals
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-dz16ku-pt-dz16ke-pt-ds16kd-sm11.pdf
Date

View Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man11) Other Service Manuals online

1. Adjustment item and a procedure    ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-2
1. 1. Lighting area adjustment
1. 3. Lens calibration
1. 4. EEPROM data transfer
1. 5. Model information setup
1. 6. Clog sensor calibration
1. 7. Contrast adjustment
2. Software Update procedure  ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-9
2. 1. Update by the LAN terminal connection
 
2. 2. Update by the SERIAL terminal connection
CONTENTS
SECTION 3
ADJUSTMENTS
Model No.
PT-DZ16KU
PT-DZ16KE
PT-DZ16KD
SECTION 3  ADJUSTMENTS
<PT-DZ16K>
1. Adjustment item and a procedure
When the following components are replaced, adjust each item according to the table below.
  1. 1. Lighting area adjustment
    1. 1. 1. Confirmation of the lighting area
1. After replacing the DMD block or each Analysis block part, 
    check if any shade is visible in the DMD effective display area.
* Make the projection environment as dark as possible and project an all-white
  and all-black pattern (internal test pattern) to conduct this check.
2. When the Lighting area interferes with the effective area, adjust the 
    Relay Lens Holder.
    1. 1. 2. Adjustment procedure of the Lighting area
 1.4. EEPROM data transfer
 1.6. Clog sensor calibration
 A-P.C.Board
 Save data to a PC before A-P.C.B exchange once and
 write in the data which saved at a new A-P.C.B.
 G-P.C.Board / M2-P.C.Board
 1.5. Model information setup
 A-P.C.Board
 When "1.4 EEPROM data transmission" was finished,
  it is not necessary.
 DMD Block / Iris unit
 DMD block / Each Analysis block part
Replaced Component
Remarks
Adjustment Item
 1.1. Lighting area adjustment
 DMD block
 Stepper motor (H/V/F)
 When a power supply was cut during shift / focus
movement, carry it out.
 1.2. Electrical convergence adjustment
 1.3. Lens calibration
 1.7. Contrast adjustment
Lighting area
Effective area
ADJ - 2
    1. 1. 2. Adjustment procedure of the Lighting area
1. Select the "QUAD" of [LAMP SELECT], projection the "APL30%" of [TEST PATTERN].
2. Loosen the 2 fixed screw with a hexagon wrench (2.5mm).
3. 1) In advance, adjust the adjustment screw that lighting
         area adjustment bracket clearance becomes 6mm.
    2) Adjustment groove, must have adjusted to the center.
4. The "Adjustment screw" is adjustment the horizontal
     direction of the Lighting area.
* The Lighting area moves to the rightward when turn
  a screw in the clockwise.
5. The "Adjustment groove" is adjustment the vertical
    direction of the Lighting area.
* The Lighting area moves to the under when turn
  in the clockwise.
6. After adjustment completion, tighten two "fixed screw".
Adjustment
groove
Adjustment
screw
Fixed
screw
6mm
Lighting area
Effective area
Adjustment screw
Adjustment groove
ADJ - 2
SECTION 3  ADJUSTMENTS
<PT-DZ16K>
  1. 2. Electrical Convergence Adjustment
It is a function to correct a convergence by a pixel unit every R/G/B ingredient.
When adjust the DZ/DS models, because it uses the entire pixel of DMD, the edge pixel of the projection
screen is missing.
1. Projected cross-hatch pattern, confirm a position gap of R/G/B.
2. Setting to service mode, and select sub menu "CONVERGENCE" of main menu "EXTRA OPTION".
3. Select a color to be adjusted.
4. Press " ▲ " " ▼ " to vertical direction Adjustment, Press "
 " "  " to horizontal direction Adjustment.
*Default : 0
ADJ - 3
5. After adjustment completion, resetting to user mode.
  1. 3. Lens calibration
1. Select sub menu "LENS CALIBRATION" of main menu "PROJECTOR SETUP".
2. Because a confirmation message is displayed, select "OK".
3. The lens will move vertically and horizontally, and the limit value of the lens shift and home position are set 
    automatically.
4. When the lens has been completely stopped, calibration is complete.
* If the lens calibration has been correctly executed, a message [COMPLETE] will appear.
  If the calibration has not been correctly executed, a message [INCOMPLETE] will appear.
*Default : 0
*Variable range of adjustment
VERTICA :  -64 ~ 0
HORIZONTAL : 0 ~ 16
ADJ - 3
SECTION 3  ADJUSTMENTS
<PT-DZ16K>
  1. 4. EEPROM data transfer
* The EEPROM data transfer via LAN terminal or serial terminal.
    1. 4. 1. Equipment to be used
1. Computer : Use it for the transfer of backup data.
2. Communication cable
・ Case of serial terminal connection : D-sub 9pin (male/female RS-232C straight)
・ Case of LAN terminal connection : LAN cable. (When connecting directly, use a cross cable)
3. Service Software : [DataLogBackup.exe] Service software is downloaded from the projector service homepage.
    1. 4. 2. Connection preparations
1. In the case of serial terminal connection
・ Confirm the RS-232C settings (ID, Baudrate  and Parity) and take a note.
2. In the case of LAN terminal connection
・ Confirm the network IP address of the projector and take a note.
・ Set the IP address of computer to approximate value of projector IP address.
3. Connect the projector and the PC by using a communication cable.
[Note]
Set up your computer not to standby or shutdown.
Serial terminal connection
LAN terminal connection
ADJ - 4
    1. 4. 3. Backup the EEPROM data (It is before circuit board exchange)
1. Switch the projector to "Normal-Standby" mode (POWER indicator is Lighting in red).
2. Start up service software [DataLogBackup.exe] with a computer.
3. 1) Select "Option " → " Setting".
    2) Select the connection method, enter the setting information of the projector.
ADJ - 4
Page of 14
Display

Download Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man11) Other Service Manuals

Here you can view online or download Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man11) Other Service Manuals in pdf. This Other Service Manuals can help you recover, restore, fix, disassemble and repair Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man11) Projector. Information contained in Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man11) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).