DOWNLOAD Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Service Manual ↓ Size: 524.22 KB | Pages: 14 in PDF or view online for FREE

1. Adjustment item and a procedure 　　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-2

1. 1. Lighting area adjustment

1. 3. Lens calibration

1. 4. EEPROM data transfer

1. 5. Model information setup

1. 6. Clog sensor calibration

1. 7. Contrast adjustment

2. Software Update procedure　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-9

2. 1. Update by the LAN terminal connection

 

2. 2. Update by the SERIAL terminal connection

SECTION 3  ADJUSTMENTS

<PT-DZ16K>

When the following components are replaced, adjust each item according to the table below.

1. After replacing the DMD block or each Analysis block part, 

    check if any shade is visible in the DMD effective display area.

* Make the projection environment as dark as possible and project an all-white

  and all-black pattern (internal test pattern) to conduct this check.

2. When the Lighting area interferes with the effective area, adjust the 

    Relay Lens Holder.

    1. 1. 2. Adjustment procedure of the Lighting area

 1.4. EEPROM data transfer

 1.6. Clog sensor calibration

 A-P.C.Board

 Save data to a PC before A-P.C.B exchange once and
 write in the data which saved at a new A-P.C.B.

 G-P.C.Board / M2-P.C.Board

 1.5. Model information setup

 A-P.C.Board

 When "1.4 EEPROM data transmission" was finished,
  it is not necessary.

 DMD Block / Iris unit

 DMD block / Each Analysis block part

Replaced Component

Remarks

Adjustment Item

 1.1. Lighting area adjustment

 DMD block

 Stepper motor (H/V/F)

 When a power supply was cut during shift / focus

movement, carry it out.

 1.2. Electrical convergence adjustment

 1.3. Lens calibration

 1.7. Contrast adjustment

Lighting area

Effective area

ADJ - 2

    1. 1. 2. Adjustment procedure of the Lighting area

1. Select the "QUAD" of [LAMP SELECT], projection the "APL30%" of [TEST PATTERN].

2. Loosen the 2 fixed screw with a hexagon wrench (2.5mm).

3. 1) In advance, adjust the adjustment screw that lighting

         area adjustment bracket clearance becomes 6mm.

    2) Adjustment groove, must have adjusted to the center.

4. The "Adjustment screw" is adjustment the horizontal

     direction of the Lighting area.

* The Lighting area moves to the rightward when turn

  a screw in the clockwise.

5. The "Adjustment groove" is adjustment the vertical

    direction of the Lighting area.

* The Lighting area moves to the under when turn

  in the clockwise.

6. After adjustment completion, tighten two "fixed screw".

Adjustment

groove

Adjustment

screw

Fixed
screw

6mm

Lighting area

Effective area

Adjustment screw

Adjustment groove

ADJ - 2

SECTION 3  ADJUSTMENTS

<PT-DZ16K>

It is a function to correct a convergence by a pixel unit every R/G/B ingredient.
When adjust the DZ/DS models, because it uses the entire pixel of DMD, the edge pixel of the projection
screen is missing.

1. Projected cross-hatch pattern, confirm a position gap of R/G/B.

2. Setting to service mode, and select sub menu "CONVERGENCE" of main menu "EXTRA OPTION".

3. Select a color to be adjusted.

4. Press " ▲ " " ▼ " to vertical direction Adjustment, Press "

 " "  " to horizontal direction Adjustment.

＊Default : 0

ADJ - 3

5. After adjustment completion, resetting to user mode.

1. Select sub menu "LENS CALIBRATION" of main menu "PROJECTOR SETUP".

2. Because a confirmation message is displayed, select "OK".

3. The lens will move vertically and horizontally, and the limit value of the lens shift and home position are set 

    automatically.

4. When the lens has been completely stopped, calibration is complete.

* If the lens calibration has been correctly executed, a message [COMPLETE] will appear.
  If the calibration has not been correctly executed, a message [INCOMPLETE] will appear.

＊Default : 0
＊Variable range of adjustment

VERTICA :  -64 ～ 0
HORIZONTAL : 0 ～ 16

ADJ - 3

SECTION 3  ADJUSTMENTS

<PT-DZ16K>

* The EEPROM data transfer via LAN terminal or serial terminal.

1. Computer : Use it for the transfer of backup data.

2. Communication cable

・ Case of serial terminal connection : D-sub 9pin (male/female RS-232C straight)
・ Case of LAN terminal connection : LAN cable. (When connecting directly, use a cross cable)

3. Service Software : ［DataLogBackup.exe］ Service software is downloaded from the projector service homepage.

    1. 4. 2. Connection preparations

1. In the case of serial terminal connection

・ Confirm the RS-232C settings (ID, Baudrate  and Parity) and take a note.

2. In the case of LAN terminal connection

・ Confirm the network IP address of the projector and take a note.
・ Set the IP address of computer to approximate value of projector IP address.

3. Connect the projector and the PC by using a communication cable.

Set up your computer not to standby or shutdown.

Serial terminal connection

LAN terminal connection

ADJ - 4

1. Switch the projector to "Normal-Standby" mode (POWER indicator is Lighting in red).

2. Start up service software ［DataLogBackup.exe］ with a computer.

3. 1) Select "Option " → " Setting".

    2) Select the connection method, enter the setting information of the projector.

ADJ - 4