Panasonic FA-S280 Service Manual ▷ View online
4-3
Troubleshhooting
E5-22:Communication failure
Is the sorter cord connected
securely?
• Check connector CNT3 of the
copier.
• Check connector J101 of the
sorter PSS2 P.C.B.
NO
Is the voltage between connector
J2-5 and 7 of the sorter CPU
P.C.B. approximately 24V?
(J1-7 0n the (+) side)
YES
• Check the input and output
voltage of the sorter low voltage
power supply P.C.B..
Input voltage
DC +24V:J101
Output voltage DC +24V:J102
NO
E7-01Bin motor failure
Does the output of J6-1 (BCAMSW)
change when the bin cam switch
is turned ON/OFF?
• Switch is not mounted
correctly or switch failure.
NO
Does the output of J6-3 (BHOMSW)
change when the bin home position
switch is turned ON/OFF?
YES
• Switch is not mounted
correctly or switch failure.
Is DC+24V generated between J13-1
and 2 with the rotation of bin motor?
YES
NO
NO
• Check DC+24V of the sorter
CPU.
• Check input/output voltage of
sorter PSS.
Input DC+24V: J101
Output DC+24V: J102
Bin motor failure.
YES
• The bin upper limit switch is turned ON when the bins are lifting up.
• The bin lower limit switch is turned ON when the bins are lifting down.
4-4
Troubleshhooting
Light
Function
Sorter
detection
detection
Bin cam
home
position
sensor
home
position
sensor
Home
position
sensor
position
sensor
Condition
Sorter is installed
Sorter is not installed
in home position
not in home position
in home position
not in home position
Code
No.
22
23
0
1
2
4
5
6
7
Message display
(FP-7728)
a)
b)
a)
b)
c)
d)
3
4.2 Service mode
(1) F4 mode
1) Input check
Copy density indicator
(FP-7718/7722)
Dark
Lights
OFF
OFF
*
Code
88
89
90
2) Output check
Started by "Copy start" key operation.
Released by "Clear/Stop" key operation or at the end of operation.
Item
Transport motor
Bin movement (Up direction)
Bin movement (down direction)
Function
The motor is energized.
The #1 bin or other bin position moves
to #10 bin position.
The #10 bin or other bin position moves
to #1 bin position.
to #10 bin position.
The #10 bin or other bin position moves
to #1 bin position.
5-1
Unpacking/
Installation
Section V
Unpacking/Installation
Unpacking/Installation
5.1 Installation requirements
• The same as the copier, FA-S280 is a precision machine. The performance of the
sorter can be affected by the surrounding conditions.
(1) The sorter should not be installed under the following conditions:
(1) Extremely high temperature/humidity.
(2) In areas exposed to direct sunlight.
(3) In areas of high dust concentration.
(4) In areas with poor ventilation.
(5) In areas of chemical fume concentration.
(6) In areas with excessive vibrations.
(7) Directly in air conditioning flow.
Note: If the copier is installed under the above conditions, suggest that the
customer move it to an appropriate place.
(2) Check the following requirements before installing FA-S280.
(1) The space shown below is needed for installation.
(2) Make sure that only accessories made by Panasonic are used.
• System consoles:
FA-DS72
(3)
Make sure the copier is operating normally before installing FA-S280.
59"/1500mm
40"/1000mm
4"/100mm
5-2
Unpacking/
Installation
Please keep this procedure.
Remove the shipping materials before the installation.
Caution : Make sure the copier is unplugged before the installation.
5.2 Installation procedure
Location
Shipping material/Procedure
Check
1
1
Remove the copier left cover.
(3 screws)
2
Remove the pre-stamped holes (4
positions) knock out from the copier
left cover.
3
Reinstall the copier left cover.
(3 screws)
2
Install the paper guide to the copier exit
door cover.
(2 screws, M4 x 12)
3
Install the magnet catch plate to the copier
exit door cover.
(1 screw)
4
Temporarily install the rail assembly
mounting screws (4 screws) to the copier
left cover.
Magnet catch plate
Pre-stamped hole
Paper guide
Rail assembly
mounting screw
mounting screw
Click on the first or last page to see other FA-S280 service manuals if exist.