Panasonic DP-2000 / DP-2500 / DP-3000 Service Manual ▷ View online
45
(57) 1 Screw (19).
(58) Remove the Reversing Guide 2 Bracket (1775)
(58) Remove the Reversing Guide 2 Bracket (1775)
Assembly.
(59) 10 Screws (B4).
(60) Remove the ADF Unit.
(60) Remove the ADF Unit.
(61) 1 Screw (19).
(62) Remove the Stamp Solenoid (1635).
(63) 2 Screws (19).
(64) Remove the Upper Feed Guide (1861)
(62) Remove the Stamp Solenoid (1635).
(63) 2 Screws (19).
(64) Remove the Upper Feed Guide (1861)
Assembly.
(65) Carefully turn the ADF Unit upside down.
(66) 1 Screw (19).
(67) Remove the Reversing Guide 1 Spring (1771).
(68) Remove the Reversing Guide 1 Bracket (1772)
(66) 1 Screw (19).
(67) Remove the Reversing Guide 1 Spring (1771).
(68) Remove the Reversing Guide 1 Bracket (1772)
Assembly.
(58)
(57)
(59)
(59)
(59)
(59)
(60)
(59)
(62)
(64)
(63)
(61)
(68)
(66)
(67)
46
(69) Disconnect the AMT Harness (1936) from the
Clutch.
(70) Remove the Snap Ring (B9).
(71) Remove the Clutch (1260).
(72) Remove 2 Snap Rings (B9).
(73) Remove the Feed 2 Roller (1753).
(74) Open the ADF Exit Cover (1854) Assembly and
(71) Remove the Clutch (1260).
(72) Remove 2 Snap Rings (B9).
(73) Remove the Feed 2 Roller (1753).
(74) Open the ADF Exit Cover (1854) Assembly and
remove in the direction of the arrow.
(75) Remove the EXT Harness (1943) from 4
Clamps.
(76) 2 Screws (19).
(77) Remove the Feed 2 Roller Guide (1754)
(77) Remove the Feed 2 Roller Guide (1754)
Assembly.
Note 1:
When re-installing the Feed 2 Roller Guide, make
sure that the Feed 2 Roller Guide is inside of the
hook on the Front ADF Bracket.
sure that the Feed 2 Roller Guide is inside of the
hook on the Front ADF Bracket.
Note 2:
When re-installing the Clutch, make sure that the
hook of the Clutch is properly placed into the notch
of the Rear ADF Bracket.
hook of the Clutch is properly placed into the notch
of the Rear ADF Bracket.
(73)
(72)
(72)
(74)
(71)
(69)
(70)
(76)
(77)
(76)
(75)
47
(78) 1 Screw (19).
(79) Disconnect the Connector from the Sensor.
(80) Release the Latch Hooks and remove the
(80) Release the Latch Hooks and remove the
Sensor (Eject Sensor) (1045).
Note:
Note:
Do not break the Latch Hooks when removing
or re-installing the Sensor.
or re-installing the Sensor.
(81) 1 Screw (19).
(82) Disconnect the Connector from the Sensor.
(82) Disconnect the Connector from the Sensor.
(83) Remove the Sensor C Actuator (1756).
(84) Release the Latch Hooks and remove the
(84) Release the Latch Hooks and remove the
Sensor (Duplex Eject Sensor) (1045).
(78)
(80)
(79)
(81)
(82)
(84)
(83)
48
Note:
When re-installing the EXT Harness (1943), make
sure to route the Harness along the hooks as
illustrated to prevent paper jams.
sure to route the Harness along the hooks as
illustrated to prevent paper jams.
< Removing ADF Cover Assembly>
(1) Open the ADF Cover (1831).
(2) Remove the ADF Rear Cover (1601) and the
(2) Remove the ADF Rear Cover (1601) and the
ADF Front Cover (1637). (See step (14) and
step (50))
step (50))
(3) Lower the ADF Input Tray back in place.
(4) Move the Lower Feed Guide (1873) Assembly
(4) Move the Lower Feed Guide (1873) Assembly
in the direction of the arrow.
(5) Release the hooks on both sides to open the
ADF Cover (1831) Assembly wide.
(6) Remove the Lower Feed Guide (1873)
Assembly.
(7) Disconnect the Connector CN29.
(8) Remove the B1S Harness (1940) from 4
(8) Remove the B1S Harness (1940) from 4
Clamps.
(9) Remove the ADF Cover (1831) Assembly.
(4)
(5)
(5)
(6)
(8)
(7)
(9)
(8)
Click on the first or last page to see other DP-2000 / DP-2500 / DP-3000 service manuals if exist.