Panasonic DP-1520P / DP-1820P / DP-1820E Service Manual ▷ View online
Order Number: MGCS040402C0
H21
Digital Imaging Systems
DP-1520P/1820P/1820E
[ Version 1.0 ]
This service information is designed for experienced repair technicians only and is not intended for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
WARNING
2
The contents of this Service Manual and the Specifications are
subject to change
without notice.
Panasonic Communications Co., Ltd. reserves the right to make improvements in
the product design without reservation and without notice.
Published in Japan.
Panasonic Communications Co., Ltd. reserves the right to make improvements in
the product design without reservation and without notice.
Published in Japan.
Information regarding Lead-Free (PbF) solder:
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a mark following
the PCB part numbers in a label on the PCB.
the PCB part numbers in a label on the PCB.
Caution:
Pb free solder has a higher melting point than standard solder; typically
the melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering iron
with temperature control and adjust it to 700 20 F (370 10 C). Exercise care
while using higher temperature soldering irons, do not heat the PCB for too long
to prevent solder splash or damage to the PCB.
Pb free solder will tend to splash when heated too high (about 1100 F/600 C).
ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:
the melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering iron
with temperature control and adjust it to 700 20 F (370 10 C). Exercise care
while using higher temperature soldering irons, do not heat the PCB for too long
to prevent solder splash or damage to the PCB.
Pb free solder will tend to splash when heated too high (about 1100 F/600 C).
ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:
URL: http://www.senju-m.co.jp) is recommended when repairing PbF PCBs.
This Product Uses Lead (Pb) Free Solder Printed Circuit
Boards (PCBs).
Boards (PCBs).
3
Important Notice
Please read this notice completely BEFORE installing any optional
accessories. As failure to properly install the additional board or
connector with the power ON could damage the machine's SPC or
SC board.
Please follow the instructions below:
Please follow the instructions below:
1. It is essential that you turn OFF the Main Power Switch located
on the Right Side of the machine.
2. It is essential that you unplug the AC Power Cord from the wall
outlet. (During a Lightning Storm, to prevent electrocution
disconnect the Telephone Line Cable first before unplugging the
AC Power Cord, if the Fax option is installed.)
3. Please read the installation instructions carefully and follow each
step.
on the Right Side of the machine.
2. It is essential that you unplug the AC Power Cord from the wall
outlet. (During a Lightning Storm, to prevent electrocution
disconnect the Telephone Line Cable first before unplugging the
AC Power Cord, if the Fax option is installed.)
3. Please read the installation instructions carefully and follow each
step.
<Example: DP-1820E>
Note:
O = Power OFF, l = Power ON
Note:
If the Hard Disk Drive Unit is installed, to prevent a Scan Disk Function from being
performed (similar to Windows OS when the power is abruptly interrupted), it is
important to follow the step sequence below when turning OFF the Power Switch on the
machine.
performed (similar to Windows OS when the power is abruptly interrupted), it is
important to follow the step sequence below when turning OFF the Power Switch on the
machine.
1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the
Right Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)",
continue to step 2 below.
2. Press "FUNCTION" and "ENERGY SAVER" keys simultaneously first.
3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive
Unit and advances into "ENERGY SAVER MODE".
4. Turn the Power Switch on the Right Side of the machine to the OFF position.
5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the
Telephone Line Cable first before unplugging the AC Power Cord, if the Fax option is installed.)
Right Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)",
continue to step 2 below.
2. Press "FUNCTION" and "ENERGY SAVER" keys simultaneously first.
3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive
Unit and advances into "ENERGY SAVER MODE".
4. Turn the Power Switch on the Right Side of the machine to the OFF position.
5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the
Telephone Line Cable first before unplugging the AC Power Cord, if the Fax option is installed.)
* The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves
the right to make improvements in the product design without reservation and without notice.
the right to make improvements in the product design without reservation and without notice.
4
Important
Before installing optional Paper Tray(s), ensure the two (2)
Brackets located on the Rear of the Copier and each
preceding Paper Tray is removed first.
Brackets located on the Rear of the Copier and each
preceding Paper Tray is removed first.
Note: It is not necessary to remove these brackets from
the bottom Paper Tray of your configuration or the
Copier if it is being placed on a Plain Stand.
Copier if it is being placed on a Plain Stand.
Do not remove these brackets
from the bottom Paper Tray of
your configuration.
from the bottom Paper Tray of
your configuration.
4th Paper Tray
3rd Paper Tray
2nd Paper Tray
Main Unit