Panasonic DP-1510P / DP-1810P Service Manual ▷ View online
21
Left Platen Cover (113)
Right Platen Cover (112)
Scanner Unit
Glass L Assembly (117)
Glass S (116)
Thermistor Assembly (944)
Thermostat (947)
Thermal Fuse (948)
Scanner Lamp (501)
Scanning Motor (131)
Inverter PC Board (564)
FPC Cable (547)
2-2-5
Registration Roller (1162)
Process Unit Guide (1142)
Toner Sensor (1147)
Separation Pad (659)
2-2-12
2-2-13
Fuser Lamp (924)
Exit Lower Guide (902)
Separator (923)
Heat Roller (913)
Exit Roller (912)
Pressure Roller (914)
Fuser Unit
Harness Guide (906)
2-2-11
Paper Feed Roller (679)
Bias Transfer Roller (648)
Roller Cleaner (640)
Control Panel Unit
LCD Cover (201)
PNL2 PC Board (1417)
PNL6 PC Board (1416)
Panel Cover (202)
2-2-4
22
Process Unit
Toner Waste Container
OPC Drum (1001)
Bias Charge Roller (1036)
Scoop Sheet (1033)
Cleaning Blade Assembly (1035)
Front & Rear Cleaning Felt (1031, 1032)
Cleaning Sponge (1030)
2-2-16
Feed Roller (1213)
2-2-14
Reverse Clutch (1212)
C25 Gear Roller (1207)
Mag Roller Joint (1047)
Mag Roller (1048)
Gap Roller (1049)
Dr. Blade Assembly (1040)
Development Felt (1041)
23
2.2.
Disassembly Instructions
2.2.1.
Power Cord, Recording Paper Tray, Process Unit
(1) Turn the Power Switch to the OFF (O) position.
(2) Disconnect the AC Power Cord (1502).
(2) Disconnect the AC Power Cord (1502).
(3) Remove the Paper Tray.
(4) Open the Right Cover (601).
(5) Open the Front Door Cover (102).
(6) Remove the Toner Waste Container by slowly
(5) Open the Front Door Cover (102).
(6) Remove the Toner Waste Container by slowly
pulling it towards the left as illustrated.
(7) Seal the Container with the enclosed cap and
dispose of it properly.
(8) Lift the Release Latch (White) and remove the
Process Unit.
(1)
(2)
(3)
(7)
(5)
(6)
(4)
(8)
24
2.2.2.
ADF Unit
(1) Open the ADF Cover (418) and release the ADF
Cover Stopper (414).
(2) Remove the Pad Cover (427).
(3) Remove the Separation Rubber (428).
(3) Remove the Separation Rubber (428).
(4) 2 Screws (19).
(5) Remove the ADF Cover (418).
(6) Disconnect the ADF Harness (1836).
(6) Disconnect the ADF Harness (1836).
(7) Remove the Pick Up Spring (426).
(8) Remove 2 Snap Rings (G3).
(9) Remove the Clutch (1141).
(8) Remove 2 Snap Rings (G3).
(9) Remove the Clutch (1141).
(10) Remove 2 Bushings (410).
(3)
(2)
(1)
(4)
(4)
(5)
(6)
(8)
(10)
(7)
(10)
(8)
(9)
Click on the first or last page to see other DP-1510P / DP-1810P service manuals if exist.