Panasonic DP-1510P / DP-1810P / DP-1810F / DP-2010E Service Manual ▷ View online
37
DP-1510P/1810P
/1810F/2010E
APR 2002
Edition 2.0
(11) Remove Roller Holder (430) Assembly.
(12) Remove the Paper Feed Shaft Assembly
(433).
Note:
When re-installing, make sure that the Roller
Holder (430) Assembly is properly placed on the
ADF Unit.
Holder (430) Assembly is properly placed on the
ADF Unit.
(13) Remove Paper Feed Roller (679) and D26 D
Gear (429).
(14) Remove the Pre Feed Roller (420), Pre Feed
Shaft (421) and Pre Feed Gear 1 and 2 (422,
423).
423).
(15) 2 Silver Screws (B1).
(16) Lift cover and release the Latch Hook then
(16) Lift cover and release the Latch Hook then
remove the ADF Rear Cover (301).
(11)
(12)
(B)
(A)
(13)
(14)
(14)
(15)
(16)
38
APR 2002
Edition 2.0
DP-1510P/1810P
/1810F/2010E
Note:
When re-installing the ADF Rear Cover (301),
make sure that the ADF Harness is properly
placed as shown in the illustration.
make sure that the ADF Harness is properly
placed as shown in the illustration.
(17) 1 Screw (19).
(18) Remove the ADF PC Board Cover (453).
(19) Release the Clamp from ADF Unit.
Note:
(18) Remove the ADF PC Board Cover (453).
(19) Release the Clamp from ADF Unit.
Note:
Do not cut the Tie-Wrap. Push the release clip on
the side of the clamp to remove it.
the side of the clamp to remove it.
(20) Disconnect the Harness (1806) on the ADF PC
Board (CN21).
(21) 2 Silver Screws (B1).
(22) Remove 2 Angle Plate (305).
(22) Remove 2 Angle Plate (305).
(23) Open the ADF Unit.
(24) 4 Screws (6A).
Caution:
(24) 4 Screws (6A).
Caution:
Don’t close the ADF Unit subsequent to this step.
(25) Remove the ADF Unit.
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
39
DP-1510P/1810P
/1810F/2010E
APR 2002
Edition 2.0
(26) Disconnect 5 Harnesses (1836, 1837, 1838,
1839, 1840) on the ADF PC Board. (6
connectors)
connectors)
(27) 2 Screws (19).
(28) Remove the ADF PC Board (1406).
(28) Remove the ADF PC Board (1406).
(29) Release the Harness from the Clamp.
(30) Disconnect 2 Harnesses (1836, 1838).
(31) 7 Screws (19).
(32) Remove the Motor Bracket (439) Assembly.
(30) Disconnect 2 Harnesses (1836, 1838).
(31) 7 Screws (19).
(32) Remove the Motor Bracket (439) Assembly.
Note:
When re-assembling the Motor Bracket (439)
Assembly, follow the steps as illustrated.
Assembly, follow the steps as illustrated.
(33) 2 Screws (18).
(34) Remove the ADF Motor (437).
(34) Remove the ADF Motor (437).
(26)
(26)
(27)
(28)
(31)
(31)
(31)
(31)
(32)
(30)
(29)
(29)
1
5
6
7
4
3
2
(34)
(33)
40
APR 2002
Edition 2.0
DP-1510P/1810P
/1810F/2010E
(35) Remove 2 Drive Belts (444, 445).
(36) Remove the S27 Pulley (443).
(37) Remove the Bushing (410).
(38) Remove the Snap Ring (B9).
(39) Remove the S27 Pulley (443).
(40) Remove the Bushing (410).
(41) Release the clips and remove the Switch (724).
Note:
(36) Remove the S27 Pulley (443).
(37) Remove the Bushing (410).
(38) Remove the Snap Ring (B9).
(39) Remove the S27 Pulley (443).
(40) Remove the Bushing (410).
(41) Release the clips and remove the Switch (724).
Note:
Apply Molykote EM-50L Grease to 3 shafts on
Bracket R (447).
Bracket R (447).
<Turn the ADF upside down>
(42) Remove the edge of the Scanning Pad (338).
(43) 1 Screw (19).
(44) Remove the Exit Roller (316) and P6L8
(43) 1 Screw (19).
(44) Remove the Exit Roller (316) and P6L8
Bushing (317).
(45) 8 Screw (1N).
(46) Remove the Hinge Units L and R.
(47) Release 2 Latch Hooks.
(46) Remove the Hinge Units L and R.
(47) Release 2 Latch Hooks.
<Return the ADF to its upright position>
(48) Remove the ADF Front Cover (302).
(49) Release the Harnesses (1837, 1839) from the
(49) Release the Harnesses (1837, 1839) from the
Clamp.
(50) 5 Screws (19).
(51) Remove the Original Tray.
(51) Remove the Original Tray.
(35)
(36)
(37)
(41)
(40)
(39)
(38)
(43)
(44)
(42)
(46)
(45)
(45)
(45)
(47)
(50)
(48)
(50)
(51)
(49)
Click on the first or last page to see other DP-1510P / DP-1810P / DP-1810F / DP-2010E service manuals if exist.