DOWNLOAD Panasonic TX-PR65VT30 Service Manual ↓ Size: 8.74 MB | Pages: 127 in PDF or view online for FREE

33

1. Remove the Plasma panel section from the servicing

stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
downward.

2. Unlock the cable clampers to free cable.
3. Remove the Stand bracket fastening screws (

×6 , 

×4

) and the Stand bracket.

1. Remove the SP shield metal L. (See section 9.15.)
2. Remove the Stand bracket. (See section 9.17.)
3. Remove the screw (

×1 ).

4. Remove the claws (

×3 ).

5. Disconnect the connector (K1) and remove the K-Board

from the LED panel.

1. Remove the SP shield metal L. (See section 9.15.)
2. Remove the screws (

×2 ).

3. Disconnect the connector (S10) and remove the S-Board.

1. Remove the SP shield metal R. (See section 9.15.)
2. Remove the Stand bracket. (See section 9.17.)
3. Remove the screw (

×1 

) and remove the claws (

×3

).

4. Disconnect the connector (V14) and remove the V-Board

from the 3D emitter panel.

1. Remove the SP shield metal (L, R). (See section 9.15.)
2. Remove the screws (

×2 

 each) and remove the Han-

dles (L, R).

34

1. Remove the Speakers. (See section 9.15.)
2. Remove the Stand bracket. (See section 9.17.)
3. Remove the K, S and V-Board. (See section 9.18 - 20.)
4. Remove the Handles. (See section 9.21.)
5. Remove the screws (

×4 

) and remove the Bottom cab-

inet assy.

1. Remove the Plasma panel section from the servicing

stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
downward.

2. Remove the Bottom cabinet assy. (See section 9.22.)
3. Remove the screws (

×8 , 

×24 ).

4. Remove the Plasma panel section from the Cabinet assy.

1. Remove the Cabinet assy. (See section 9.23.)
2. Remove the Tape from the Contact metals.
3. Remove the screws (

×21 ).

4. Remove the Contact metal side (L, R).
5. Remove the screws (

×8 ).

6. Remove the Contact metal top.
7. Remove the screws (

×15 ).

8. Remove the Contact metal bottom.

1. Remove the Contact metal bottom. (See section 9.24.)
2. Disconnect the flexible cables (CB1, CB2 and CB3).
3. Disconnect the flexible cable (C10).
4. Disconnect the connector (C14).
5. Remove the screws (

×3 

) and remove the C1-Board.

35

1. Remove the Contact metal bottom. (See section 9.24.)
2. Disconnect the flexible cables (CB4, CB5, CB6, CB7,

CB8 and CB9).

3. Disconnect the flexible cables (C20, C21 and C26).
4. Remove the screws (

×4 

) and remove the C2-Board.

1. Remove the Contact metal bottom. (See section 9.24.)
2. Disconnect the flexible cables (CB10, CB11, CB12,

CB13, CB14 and CB15).

3. Disconnect the flexible cables (C31 and C36).
4. Disconnect the connector (C35).
5. Remove the screws (

×4 

) and remove the C3-Board.

1. Remove the screws (

×14 , 

×2 

) and remove the AL

frames.

2. Remove the screws (

×4 

 each) and remove the Corner

fixing metals.

1. Place a carton box packed a new Plasma panel on the

flat surface of the work bench.

2. Open a box and without taking a new Plasma panel.
3. Attach the Cabinet assy and each P.C.Board and so on,

to the new Plasma panel.

36

When Plasma panel or A-board is replaced, Vsus should be set to LOW or HIGH.

1. Go into main item [VSUS] in Service Mode. LOW or HIGH will be displayed.
2. Press [OK] button to go to TEST stage. 

White pattern without On-Screen Display will be displayed during TEST and CONF stage. Press [5] button to display the 
On-Screen Display.

3. Press [VOL (-)] button to set to LOW.
4. In LOW setting

a. If no several dead pixel is visible remarkably in white pattern, press [3] button to go to CONF stage.
b. If the several dead pixels are visible remarkably in white pattern, Set to HIGH by press [VOL (+)] button. Press [3] button

to go to CONF stage if the symptom is improved. 

5. Press [OK] button in CONF stage to store LOW or HIGH.
6. Exit Service Mode by pressing [Power] button.