DOWNLOAD Panasonic TX-PR50VT30 Service Manual ↓ Size: 8.22 MB | Pages: 127 in PDF or view online for FREE

9

* The battery deteriorates after repeated use, and the operation time eventually becomes short. Number of charging cycles may decrease
depending on the operating conditions. During the long period of disuse, charge fully once every 6 months to keep the performance. The fig-
ures above are at shipping from the factory, and are not a guarantee of performance.

• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.

10

1. EEPROM (IC8902) for spare parts has the seed of KEY for each.
2. The final KEY data will be generated by Peaks IC (IC8000) when SELF CHECK was done and are stored in both Peaks IC

(IC8000) and EEPROM (IC8902).
Three KEY are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.

When Peaks IC (IC8000) is replaced, EEPROM (IC8902) should be also replaced with new one the same time.
When EEPROM (IC8902) is replaced, Peaks IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more
than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.

Model No.

Keys

One-to-One

(For USB Rec.)

CI Plus

DTCP-IP

WIDEVINE

TX-PR50VT30

None

None

None

Yes

11

The Service port (M3 mini Jack) on the following TVs can use as the RS232C terminal which is a standard computer SERIAL inter-
face.
 *This operation system should be used by the certified professional dealer.

• The TV can be controlled by a personal computer when connected through an RS232C/ M3 mini jack conversion cable (not sup-

plied).

• The computer will require software which allows sending and receiving of control data through its SERIAL port.

Please see required parameters and commands below.

The transmission of control data from the PC starts with a STX signal, followed by the command, the parameters, and lastly an
EXT signal in that order. If there are no parameters, then the parameter signal does not need to be sent.
*Please see other side regarding Commands and Parameters.

• With standby mode, this TV responds to "PON" and "QPW" commands only.
• Wait for the response of the first command to come from this unit before sending the next command.
• If multiple commands are transmitted, be sure to keep intervals of 250 m sec.

Send the command again when the call back command is unusual.

• If an incorrect command is sent by mistake, this TV will send an "ER401" or "ER402" command back to the computer.
• This TV does not respond for 15 seconds when "PON" or "POF" commands are transmitted.
• Send "EXT" commands before sending "IMS:**" commands.
• MUTE commands ("AMT: 0" and "AMT: 1") and "AVL: ***" command are invalid in case of HDMI (CECIL) cooperation.

However AMT, AUK, AUDI commands is effective. (MUTE rotation (toggle), VOLUME UP and VOLUME DOWN controls are
possible.)

Signal level 

RS-232C compliant

Synchronization method 

Asynchronous

Baud rate 

9600 bps

Parity None

Character length 

8 bits

Stop bit 

1 bit

Flow control 

-

12

Control 

Command

Inquiry 

Command

Call back 

Command

Parameter

note

STANDARD 

CONTROL

POWER ON

PON

QPW

QPW : *

"0"(OFF)/ "1"(ON)

POWER OFF

POF

VOL

(level)

AVL: ***

QAV

QAV : ***

"000" - "100"

(up)

AUU

(down)

AUD

MUTE

AMT (Toggle)

QAM

QAM : *

"0"(NO MUTED)

/ "1"(MUTED)

AMT: *

ASPECT

DAM: ****

QAS

QAS : **** "ZOOM"/"FULL"/

"JUST"/"NORM"/

"SELF"/"ZOM2"/
"ZOM3"/"SFUL"/

"14:9"

Except SD mode

DAM (Tog-

gle)

INPUT 

SELECT

CH UP

CHU

--

--

--

CH DOWN

CHD

--

--

--

TV

IMS : TV

QMI

QMI : **

"TV"

TV network (Toggle)

Analogue TV

IMS : TVA

"TVA"

DVB-T

IMS : TVD

"TVD"

DVB-S/Other Sat

IMS : BS1

"BS1"

Freesat

IMS : BS2

"BS2"

DVB-C

IMS : CAB

"CAB"

Component 1

IMS : C1

"C1"

Component2

IMS : C2

"C2"

Video 1

IMS : V1

"V1"

Video 2

IMS : V2

"V2"

Video 3

IMS : V3

"V3"

S-Video 1

IMS : S1

"S1"

SCART Cable

S-Video 2

IMS : S2

"S2"

SCART Cable

HDMI 1

IMS : H1

"H1"

HDMI 2

IMS : H2

"H2"

HDMI 3

IMS : H3

"H3"

HDMI 4

IMS : H4

"H4"

PC

IMS : PC

"PC"

SD (photo viewer)

IMS : SP

"SP"

VIERA CAST

IMS : VC

"VC"

PICTURE 

MODE

Vivid (Dynamic)

VPC : VVT

QPC

QPC : ***

"VVT"

Standard

VPC : STD

"STD"

THX/ True Cinema

VPC : THX

"THX"

THX : Except PC, JPEG, MOVIE & VIERA CAST

Cinema

VPC : CNM

"CNM"

Game

VPC : GAM

"GAM"

Photo

VPC : CST

"CST"

Only HDMI, JPEG, MOVIE & VIERA CAST

Pro1

VPC : PR1

"PR1"

When Advance (isfccc) menu is On.
Except VIERA CAST

Pro2

VPC : PR2

"PR2"