Panasonic TH-65PB1E Service Manual ▷ View online
21
TH-65PB1E
6.5.2.
Supplement 2: Information about registration of electronic pen
Supplement 2: Information about registration of electronic pen
Information about registration of electronic pen
You can register up to 3 electronic pens for each interactive plasma display.
Once an electronic pen has been registered, it cannot operate another interactive plasma display.
When registering or unregistering an electronic pen, be sure to turn off the power of any other interactive plasma
displays nearby.
displays nearby.
If you are registering an electronic pen for the first time, perform step 3 only. Otherwise, perform the procedure below
starting from step 1.
starting from step 1.
Registration method of electronic pen
[Procedures]
On the [Start] menu, select [All Programs] [Panasonic] [elite Panaboard] [Interactive Plasma
Display] [Pairing Tool].
Display] [Pairing Tool].
The Pairing Tool starts.
Click [Pairing].
To cancel the registration, click [Close].
Move the electronic pen you want to register close to the electronic pen adapter, hold down both the
Mouse/Pen Switching button and the Function button, and turn on the electronic pen.
Mouse/Pen Switching button and the Function button, and turn on the electronic pen.
You cannot register an electronic pen if 3 electronic pens have already been registered.
1.
2.
3.
If you are using the Pairing Tool, clicking [Cancel] cancels the registration.
On the confirmation window, click [OK].
4.
Press both of buttons
Mouse/pen
switching button
switching button
Function button
Power switch
Turn [ON]
22
TH-65PB1E
6.6.
Failure diagnosis at the time of wireless LAN fault
[1]Check of LAN microcomputer
[2]Check of Wireless module
Check the communication with the LAN microcomputer
[How to check]
The display check of "IC2004" column in a self check
or
The display check of the "LAN-MCU" column of CD mode
picture
or
The display check of the "LAN-MCU" column of CD mode
picture
IC2004
LAN-MCU
Normal
Abnormal
Display "OK"
Display the numbers
Display "----"
[Diagnostic result]
If the "Normal" judging
Go to [2] check.
If the "Abnormal" judging
Failure of the A board (LAN microcomputer)
Self check screen
[1]
[1]
[2]
CD mode screen
Status screen
[2]
[Preparations]
Turn off and turn on a main power supply before
a check. (Old information is eliminated
from a LAN microcomputer.)
a check. (Old information is eliminated
from a LAN microcomputer.)
The "MAC Address" column of the status
screen in the "Network Setup" menu
or
The "LAN-MAC (WIRELESS)" column of the
CD mode screen
screen in the "Network Setup" menu
or
The "LAN-MAC (WIRELESS)" column of the
CD mode screen
[Diagnostic result]
Normal
Abnormal
MAC Adress
LAN-MAC (WIRELESS)
Display of hexadecimal digits
Display of "--:--:--:--:--:--"
Since the main part is normal, the check of
radio environment or a setup is required for it.
Failure of the wireless module (the antenna)
in rare cases.
radio environment or a setup is required for it.
Failure of the wireless module (the antenna)
in rare cases.
Failure of the wireless module
or
Breakage of the wireless module terminal
or
Breakage of the wireless module terminal
*: Since each information is checked immediately after power supply ON, it becomes the
shown of "-- :--:--:--:--: [ -- ]."
Since an information check is carried out in the order of cable LAN and wireless
LAN, when you diagnose, please wait for a while and check the contents of a display.
Since an information check is carried out in the order of cable LAN and wireless
LAN, when you diagnose, please wait for a while and check the contents of a display.
Display "NG"
Check the communication with a Wireless module
[How to check]
If the "Normal" judging
If the "Abnormal" judging
23
TH-65PB1E
7 Service Fixture & Tools
7.1.
SC jig
Purpose:
To find the failure board (SC or SU/SD) when the power LED is blinking 7 times.
SC jig:
Jumper connector to connect to SC50 connector on SC board
Part number:
TZSC09187
How to use:
Caution: Remove SC jig from SC board after inspection.
1. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically.
Note: The board will be damaged if all connector is not removed (for example; remove connector only for SU board
and stay connecting with SD board. The board will be damaged.)
2. Connect SC jig to connector SC50 at left bottom side of SC board.
3. Turn on the TV/Display Unit and confirm the power LED blinking.
3. Turn on the TV/Display Unit and confirm the power LED blinking.
LED blinking: Possible cause of failure is in SC board
No LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board
No LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board
4. After inspection, turn off the TV/Display Unit and wait a few minutes to discharge.
5. Remove SC jig from SC board.
5. Remove SC jig from SC board.
24
TH-65PB1E
8 Disassembly and Assem-
bly Instructions
The important matter at the time of electronic pen
exchange
• Please register electronic pen, when electronic pen is
exchanged.
• There is a maximum in electronic pen's number of registra-
tion.
The important matter at the time of electronic pen adapter
exchange
• Since electronic pen's registration information is memorized
by the electronic pen adapter, in electronic pen adapter
exchange, re-registration of electronic pen is required for it.
(It is unrelated in the registration information, A module, and
the main part of a display of an electronic pen)
exchange, re-registration of electronic pen is required for it.
(It is unrelated in the registration information, A module, and
the main part of a display of an electronic pen)
The important matter in the case of exchanging modules
• To disassemble P.C.B., wait for 1 minute after power was off
for discharge from electrolysis capacitors.
•
, ,
, , , and marks indicate screw positions.
8.1.
Removal of Rear Cover
1. Remove screws (
×26 ,
×4 ,
×16 ) and M8 Cap (×4
) and then remove the Rear Cover.
2. Turn over the Reae Cover.
3. Remove the P Print Barrier (C).
3. Remove the P Print Barrier (C).
8.2.
Removal of Slot Block
1. Disconnect the connectors (DS13, P9).
2. Remove the flexible cable from the connector (DS1).
2. Remove the flexible cable from the connector (DS1).
3. Remove 4 screws and then remove the Slot Block.
8.3.
Removal of DS-Board
1. Remove the Slot Block.
(Refer to Removal of Slot Block)
2. Turn over the Slot Block.
3. Remove 6 screws and then remove DS-Board.
3. Remove 6 screws and then remove DS-Board.
8.4.
Removal of HX-Board
1. Disconnect the connectors (A37).
2. Remove 4 Hexagonal-Head screws, 4 screws ( ), 1
2. Remove 4 Hexagonal-Head screws, 4 screws ( ), 1
screws ( ), 1 screws ( ) and then remove the HX-Board
Block.
Block.
Click on the first or last page to see other TH-65PB1E service manuals if exist.