DOWNLOAD Panasonic TH-42PR11EH Service Manual ↓ Size: 20.33 MB | Pages: 127 in PDF or view online for FREE

29

TH-42PR11EH

1. Set Aging pattern (white pattern signal) by IIC mode.
2. Set the picture controls as follows.

Picture menu: Standard
Picture: +25
Aspect: Full

1. First perform Vsus adjustment.
2. Confirmation of Vscn voltage should be performed after

confirmation of Vad adjustment.
When Vad=-149V, Voltage of Vscn is -4V ±4V.

Adjust driver section voltages. (Refer to the panel data on the
Panel Label).
Check or adjust the following voltages with the multimeter. 

*See the Panel Label.

Name

Test Point

Voltage

Volume

Remarks

Vsus

TPVSUS 
(SS)

Vsus ± 2V

R628 (P)

*

Ve

TPVE (SS)

Ve ± 1V

VR6000 (SS)

*

Vset

TPVSET 
(SC)

320V + 7V, -
9V

Fixed

Vad

TPVAD (SC) -149V ± 1V

VR6600 (SC)

Vscn

TPVSCN 
(SC)

Vad+145V ± 
4V

Fixed

Vda

TPVDA (SS) 75V + 1V, -2V Fixed

PFC

C446 (+)(-)

396V ± 0.5V

R443 (P)

30

TH-42PR11EH

1. Set Aging pattern (white pattern signal) by IIC mode.
2. Set the picture controls as follows.

Picture menu: Standard
Picture: +25
Aspect: Full

3. Connect Oscilloscope to TPSC1 and adjust VR6602 for 210 ± 10V.

1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.

Adjust the following voltages with the multimeter.

*See the Panel Label.
Caution

Absolutely do not reduce Vsus voltage below Ve not to damage the P.C.B.

Test Point

Volume

Level

TPSC1 (SC)

VR6602 (SC)

210 ± 10V
at 100 

µs 

period on the down slope.

P.C.B.

Name

Test Point

Voltage

Volume

Remarks

P Board

Vsus

TPVSUS (SS)

Vsus ± 2V

R628 (P)

*

PFC

C446 (+) (-) (P)

396V ± 0.5V

R443 (P)

SC Board

Vad

TPVAD (SC)

-149V ± 1V

VR6600 (SC)

SS Board

Ve

TPVE (SS)

Ve ± 1V

VR6000 (SS)

*

D, DS, DN Board

White balance, Pedestal and Sub brightness for NTSC, PAL, HD, PC and 625i signals

DN Board

Set Market Select Number to correct destination by MS mode. (See chap. 6.1.4)

31

TH-42PR11EH

32

TH-42PR11EH

Instrument Name

Connection

Remarks

• RGB VGA W / B pattern
• Color analyzer

(Minolta CA-100 or equivalent)

PC input
Panel surface

User setting: Normal
(Picture menu: Standard)

Procedure

Remarks

[condition]

• Ensure aging is adequate.
• Make sure the front panel to be used on the final set is fitted. 
• Make sure a color signal is not being shown before adjustment.
• Put the color analyzer where there is little color variation.

1. Set COMPONET / RGB-IN SELECT to RGB.
2. Select the IIC mode “PANEL W / B Adj.” item.
3. Check that the color temperature is “COOL (High)”.
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight window’s center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the “Color temperature 

High” in the below table.

7. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
8. Set color temperature to “NORMAL (Medium)”.
9. Fix G drive at E0h and adjust B drive and R drive so the highlight window’s x, y becomes 

the “Color temperature Medium” in the below table.

10. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.

11. Set color temperature to “WARM (Low)”.

12. Set G drive to E0h and adjust B drive and R drive so the highlight window’s x, y become 

the “Color temperature Low” shown in the below table.

13. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.

Adjustment target
Hi-light: x ± 0.003 y ± 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.

Picture Menu: Standard
Picture: 25
Aspect: Full
Position and size: Normal

• Highlight section Signal amplitude 75%

• Cutoff standard G: 80h

• Drive standard G: E0h