DOWNLOAD Panasonic CF-18 (serv.man9) Service Manual ↓ Size: 3.11 MB | Pages: 66 in PDF or view online for FREE

7-4

6. Remove the I/O PCB.

Screw<O>: DFHE5025XA

<P>: DFHE5058ZB
<Q>: DRSB2+5FKL

Figure 14

1. Remove the LED Waterproof Sheet.
2. Remove the LED PCB.
3. Remove the Switch PCB.
4. Remove the Power Switch.

Figure 15

1. Remove the three Screws. <R>
2. Remove the CPU Heat Plate.
3. Remove the Lithium Battery.

Screw<R>: DFHE5025XA

Figure 16

1. Remove the four Screws. <S>
2. Remove the LCD Hinge Cover.

Figure 17

3. LCD is half-rotated. Removes the two Screws. <T>
4. Remove the Hinge Cover.

Figure 18

5. Remove the four Screws. <U>
6. Remove the Display Unit.

Screw<S>: DFHE5025XA

<T>: DRSB2+5FKL
<U>: DXYN4+J8FNL

LED Waterproof Sheet

LED PCB

Power 

Switch 

Knob

Operation Sheet

Switch PCB

<R>

<R>

<R>

CPU Heat Plate

Lithium Battery

<T>

<T>

Hinge Cover

<S>

<S>

LCD Hinge Cover

<S>

<S>

<U> <U>

<U>

<U>

7-5

Figure 19

1. Remove the sixteen Screws. <V>
2. Remove Antenna Cover and Tablet Latch Cover.
3. Remove the two Screws. <W>
4. Remove the eleven Screws. <X>
5. Remove the LCD Rear Case.

Screw<V>: DRQT26+D5FKL

<W>: DXYN3+J10FNL
<X>: DXYN2+J6FNL

Figure 20

1. Remove the two Screws. <Y>
2. Remove the Cable Holder Plate and LCD Hinge.
3. Remove the Cable Holder.
4. Remove the Cable Holder sheet.

Screw<Y>: DXYN3+J8FNL

<Z>

<Z>

Inverter Case

Connector (CN2)

Connector (CN1)

Inverter PCB

TS PS2 PCB

Connector (CN901)

Connector (CN900)

LCD Back Damper

Figure 21

1. Disconnect the two Cables from two Connectors (CN1,

CN2).

2. Remove the Inverter Case and Inverter PCB.
3. Remove the two Screws. <Z>
4. Remove the LCD Rear Damper.

Screw<Z>: DXHM0042ZA

Figure 22

1. Remove the two Screws. <a>
2. Remove the GPRS Antenna PCB.
3. Remove the two Screws. <b>
4. Remove the LAN1-BT Antenna PCB.
5. Remove the two Screws. <c>
6. Remove the LAN2 Antenna PCB.
7. Remove the Pen.
8. Remove the two Screws. <d>
9. Remove the Pen Holder.

Screw<a><b><c>: DFHE5025XA

<d>: DRHM5025YA

<Y>

<Y>

LCD Cable

Holder

Sheet

Cable

Holder

Cable

Holder

Cable

Holder

Plate

Cable Holder

Plate

Cable

Holder

Plate

LCD

Hinge

<X>

<X>

<X>

<X>

<X>

<W>

<W>

<X>

<X>

<X>

<X>

<X>

<X>

<V>

<V>

<V>

<V>

<V>

<V>

<V>

<V>

Antenna Cover

Tablet Latch Cover

LCD Rear Case

Antenna Cover

<V>

<V>

<V>

<V>

<V>

<V>

<V>

<V>

<d>

<b>

<c>

<c>

<a>

<a>

<b>

<d> Pen Holder

LAN1-BT

Antenna PCB

LAN2-BT

Antenna PCB

GPRS 

Antenna PCB

Pen

7-6

<f>

PCMCIA LID ASS'Y

DC IN LID Rubber
USB LID Rubber
LAN LID Rubber
Moden/LAN LID Rubber

Audio
LID Rubber

HDD LID ASS'Y

Battery 
LID ASS'Y

<f>

<e>

<e>

<e>

<e>

<f>

<e>

<f>

RGB
LID Rubber

Serial
LID Rubber

<f>

<f>

<f>

Figure 23

1. Remove the six Screws. <e>
2. Remove the Battery LID ASS'Y, HDD LID ASS'Y and

PCMCIA LID ASS'Y.

3. Remove the twelve Screws. <f>
4. Remove the Moden/LAN LID Rubber, LAN LID Rubber, USB

LID Rubber, DC IN LID Rubber, Serial LID Rubber, RGB
LID Rubber and Audio LID Rubber.
Screw<e>: DRQT26+D3ZKL

<f>: DRHM5025YA

CF-18JHUZBZZ

E34

K1-2

K1-1

K1-7

K1-5

K66

K83

K42

K608

K400

K37

K44

K38

K67

K53

K51

E18

K50

K19

K400

K400

K92

K81

K66

K406

K406

K406

K301

K25

K1-8

K1-10

K1-6

K1-3

K55

K55

K55

K1-4

K1-9

K1-2

K1-11

E32

K1-2

K24

K219

K1

K1-12

K33

K77

K84

K601

K601

K606

F

F

A

K89

K1-15

K708

K709

A

A

A

A

A

A

Screw tightening torque

0.2 _ 0.02N  m
  (2.0 _ 0.2kgf  cm)
0.8 _ 0.02N  m
  (8.0 _ 0.2kgf  cm)

A

F

+

+

+

+