Panasonic KX-HDV130RU / KX-HDV130RUB Service Manual ▷ View online
17
KX-HDV130RU/KX-HDV130RUB
7.2.
KEYs and LEDs Test mode
This unit has the KEYs and LEDs Test mode.
By using this mode, you can easily check KEYs and LEDs.
By using this mode, you can easily check KEYs and LEDs.
7.2.1.
Preparation
Preparation devise:
• Unit for Test phone
• AC adaptor or Ethernet cable(PoE).
• AC adaptor or Ethernet cable(PoE).
Set up a unit in KEYs and LEDs Test mode by key control
1. Push [1] [TRANSFER] [*] and connect power plug (AC adaptor/PoE).
2. Wait until LCD displays [factory mode] and release the three keys.
2. Wait until LCD displays [factory mode] and release the three keys.
7.2.2.
KEYs and LEDs Test
1. Then the LCD displays [HOOK Test].
(When skip [HOOK Test], Press SP-PHONE key. )
The RINGER LED is on/off according to HOOK switch.
Press SP-PHONE key.
The RINGER LED is on/off according to HOOK switch.
Press SP-PHONE key.
2. Then the LCD displays all dots.
Confirm all dots displayed on the LCD.
Press "0" key. All LCD displays "Q" and backlight is turn ON.
Press SP-PHONE key.
Press "0" key. All LCD displays "Q" and backlight is turn ON.
Press SP-PHONE key.
3. Then the LCD displays [Key-Check Test] . Press all keys except SP-PHONE key.
Press SP-PHONE key.
4. Then the LCD displays [Key-Check OK].
Confirm Ringer LED, Line1 LED, and Line2 LED is on.
Press SP-PHONE key.
Press SP-PHONE key.
5. Then the LCD displays the software version.
Ringer LED, Line1 LED, and Line2 LED is turn on with blue color.
Press SP-PHONE key.
Press SP-PHONE key.
6. Then the LCD displays [RESONANCE test].
Confirm speaker is functioning.
Press SP-PHONE key.
Press SP-PHONE key.
7. Then the LCD displays [ACOUSTIC TEST].
This TEST mode is not used in service. Press SP-PHONE.
8. Then the LCD displays [MODEL : KX-HDV130].
Press SP-PHONE key.
9. Then the LCD displays [PASS : ffff].Press SP-PHONE key.
10. Then the LCD displays MAC address. Press SP-PHONE key.
10. Then the LCD displays MAC address. Press SP-PHONE key.
7.2.3.
Quit KEYs and LEDs Test mode
It is OK to quit anytime during test mode. Disconnect AC adaptor or Ethernet cable(PoE).
18
KX-HDV130RU/KX-HDV130RUB
8 Service Mode
8.1.
Factory Setting
8.1.1.
How to Clear User Setting
Units are reset to the Factory settings by this operation (Erase stored Phone numbers, Caller list and etc.).
This operation should not be performed for a usual repair.
This operation should not be performed for a usual repair.
To perform IP Reset
1. Connect power plug (AC adaptor)
2. Press "1", "5", "9" and "*" at the same time until LCD displays [factory reset].
3. Wait for the reset process until it LCD displays [factory reset done].
2. Press "1", "5", "9" and "*" at the same time until LCD displays [factory reset].
3. Wait for the reset process until it LCD displays [factory reset done].
8.2.
How to Change MAC Address Label
(Procedure after Replacing the Main P.C.B.)
(Procedure after Replacing the Main P.C.B.)
When replacing the Main P.C.B., customer data shall be renewed before sticking the included MAC/Address.
8.2.1.
Replacing Main P.C.B.
Note:
(*1) : If you reuse defective P.C.B. for another repairing unit by repairing. Peel off the serial number and MAC address label on
original bottom cabinet and keep them with defective P.C.B..
(*2) : If you do not reuse the defective P.C.B. by repairing, scrap the P.C.B. to prevent the leak of customer's information in flash
ROM.
original bottom cabinet and keep them with defective P.C.B..
(*2) : If you do not reuse the defective P.C.B. by repairing, scrap the P.C.B. to prevent the leak of customer's information in flash
ROM.
19
KX-HDV130RU/KX-HDV130RUB
8.2.2.
Attaching MAC Address Label
Attach the new MAC address label to the unit by placing over the old label.
Attach the new label
NEW MAC Address Label
20
KX-HDV130RU/KX-HDV130RUB
9 Troubleshooting Guide
9.1.
No Operation
9.1.1.
Power ON Error
9.1.2.
Power Supply : AC adaptor
Yes
No
No
Yes
Related parts:
CN2, LCD module, R139-R142,
R145, L106, L108,L110, L111,
C129, C134-C137, C130-C132.
R145, L106, L108,L110, L111,
C129, C134-C137, C130-C132.
See 9.2 LCD Does Not Operate. (P.26)
Related parts: Power supply
See 9.1.2 AC Adaptor (P.20) or
See 9.1.3. PoE (P.21)
See 9.1.2 AC Adaptor (P.20) or
See 9.1.3. PoE (P.21)
Confirm the LCD Display.
Is it working?
Is it working?
When input any POWER(AC adaptor or PoE).
Does RINGER-LED (BLUE) light?
Does RINGER-LED (BLUE) light?
END
Check the soldering.
Resolder or replace parts as needed.
Resolder or replace parts as needed.
Yes
No
Related parts: F1, L210, C229, C230, D209, D210.
Confirm DC Jack assembly.
Confirm DC Jack assembly.
Check the soldering.
Resolder or replace parts as needed.
Resolder or replace parts as needed.
Measure the voltage at TP:DCIN.
Is it about 6.5V?
Is it about 6.5V?
GO TO A
*Please refer to 10.3 Assembly for Lead wire.
Click on the first or last page to see other KX-HDV130RU / KX-HDV130RUB service manuals if exist.