Panasonic KX-HDV130RU / KX-HDV130RUB Service Manual ▷ View online
13
KX-HDV130RU/KX-HDV130RUB
5 Location of Controls and Components
5.1.
Name and Locations
14
KX-HDV130RU/KX-HDV130RUB
6 Installation Instructions
6.1.
Connections
Connect the Ethernet cable, the Handset Cord and the AC adaptor (Option) to the unit.
*2
*3
*1
*1 PoE HUB
*2 Optional AC adaptor
*3 Optional headset
*2 Optional AC adaptor
*3 Optional headset
For up-to-date information about headsets that have been tested with this unit, refer to the following
web sites:
http://panasonic.net/pcc/support/sipphone/
web sites:
http://panasonic.net/pcc/support/sipphone/
The initial setting for the IP address is "DHCP—Auto". For information about your network
environment, contact your administrator.
environment, contact your administrator.
When selecting Ethernet cables (not included)
Use flexible cables without jack covers. Do not use cables with a hard coating that may tear or crack
when bent.
To prevent damage to the cables, use cables that do not protrude from the bottom of the base.
when bent.
To prevent damage to the cables, use cables that do not protrude from the bottom of the base.
Connect the cables as shown in the following illustration.
15
KX-HDV130RU/KX-HDV130RUB
7 Test Mode
7.1.
Peer to Peer Test Mode
This is for VoIP communication TEST.
Setting of Unit are required before communication test by Peer to Peer Mode.
Refer to from 7.1.1 Preparation (P.15) to 7.1.2 Connection for Test (P.16) .
Refer to from 7.1.1 Preparation (P.15) to 7.1.2 Connection for Test (P.16) .
7.1.1.
Preparation
Prepared device:
• Unit (for Test phone and Reference phone): Each one
• Ethernet (LAN) cable
• Ethernet (LAN) cable
Set up unit in test mode by key control
1. Push [2][6][*] and connect power plug (AC adaptor/PoE).
2. Wait until LCD displays [p2p mode]. Then release the three keys.
3. Then the LCD displays [P2P Mode]. Press OK.
4. Then it enters P2P Mode Setting. Choose the any mode.
2. Wait until LCD displays [p2p mode]. Then release the three keys.
3. Then the LCD displays [P2P Mode]. Press OK.
4. Then it enters P2P Mode Setting. Choose the any mode.
Normal /Test1 (192.168.0.241)/Test2 (192.168.0.240)
5. Then the LCD displays [Set OK]. Remove and reconnect the plug.
Ethernet (LAN) cable
Customer's Unit
Reference Unit
16
KX-HDV130RU/KX-HDV130RUB
7.1.2.
Connection for Test
1. Connect LAN port on Customer's unit (for reference) to LAN port on Reference unit (for test) with Ethernet (LAN) cable.
2. Plug the each unit's (for test and reference) AC adaptor or PoE HUB.
7.1.3.
Communication Test
1. Pick up handset (OFF Hook), then dial the following number (for test).
[0] [1] [2] [3]
2. Answer the call by pressing [SP-PHONE] button on unit (for reference), and confirm the voice and the display.
3. Disconnect the call by unit (for reference).
4. Pick up handset (OFF Hook), then dial the following number (for reference).
3. Disconnect the call by unit (for reference).
4. Pick up handset (OFF Hook), then dial the following number (for reference).
[0] [4] [5] [6]
5. Answer the call by pressing [SP-PHONE] button on unit (for test), and confirm the voice and display.
6. Disconnect the call by unit (for test).
6. Disconnect the call by unit (for test).
7.1.4.
Quit peer to peer Test mode
After Communication Test, set the normal mode or Factory Setting (P.18).
Ethernet (LAN) cable
Customer's Unit
Tel no: 0456
Tel no: 0456
Reference Unit
Tel no: 0123
Tel no: 0123
IP: 192.168.0.241
TEST mode 1
TEST mode 1
IP: 192.168.0.240
TEST mode 2
TEST mode 2
PoE HUB
Optional AC adaptor
Click on the first or last page to see other KX-HDV130RU / KX-HDV130RUB service manuals if exist.