DOWNLOAD Panasonic UB-T781 / UB-T781W / UB-T761 Service Manual ↓ Size: 3.11 MB | Pages: 115 in PDF or view online for FREE

17

Confirm that the following items are included with the elite Panaboard.

• Screws (8 count) for wall mounting are not included. Please purchase screws with a size of M6, appropriate for type of wall.

(Refer to section 3.4.3 Wall Types and Installation Procedures.)

18

When mounting on a wall, consult with your building's owner, caretaker or construction manager to determine if the wall strength is
sufficient to install the elite Panaboard. For safety, install the elite Panaboard only after thoroughly understanding the type of walls,
the appropriate types of screws and the construction method.
Caution

Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall mounting plate bolts to metal laths
or wire laths can cause heat, smoke or a fire.

Drill, Screwdriver, Measuring tape, Level, 8 screws (M6 size)

1. Make sure that the wall is strong enough to support the elite Panaboard.

Rated strength: greater than 1,373 N (140 Kgf)
Notice

• If necessary, reinforce the wall so that it is strong enough to support the elite Panaboard.

2. Make sure that the location is large enough to accommodate the elite Panaboard.

Height: greater than 2,100 mm (6 ft. 10

5

/

8

 in.)

Width: greater than 2,000 mm (6 ft. 6

3

/

4

 in.)

3. Make sure that the AC outlet is within 3 m (9 ft. 10 

1

/

8

 in.) of where the elite Panaboard will be mounted and that it will not be

behind the elite Panaboard.

1. Ensure that the wall is strong enough to support the elite Panaboard.

Rated strength: greater than 1,373 N (140 Kgf)

2. Using the measuring tape and level, mark the 8 locations to insert the screws.

19

• The dotted line in the illustration represents the outer edge of the elite Panaboard.

3. Drill 8 holes for the wall mounting plates.

• Drill holes that are appropriate for the screws you are using.

4. Install the wall mounting plates using the 4 screws.

• 2 screws are used for each wall mounting plate.

The remaining 4 screws are used after installing the elite Panaboard on the wall.

• Screws (8 count) are not included with the elite Panaboard. Please purchase screws with a size of M6, appropriate for type of

wall.

• Tighten the bolt so that it will not become loose.
• When drilling the holes and installing the wall mounting plates, follow the procedure in the section 3.4.3 “Wall Types and

Installation Procedures”

5. Mount the elite Panaboard on the wall.

Refer to the section 3.6 “Assembling the elite Panaboard”.

20

The method for attaching the wall mounting plates to the wall will vary depending on the wall's structure.
Three available options are listed below.
Other methods may be necessary depending on the wall.
<Metal or Concrete walls>

Stud plug (not included) are needed.

Split-wing toggles (not included) are needed.

Wood screws (not included) are needed.

Drill eight holes in the wall.
For the correct hole size, refer to the instructions for the particular stud plugs used.

Insert the bolt through the hole in the wall mounting plate and tighten until the wall
mounting plate is securely fixed to the wall.

Insert the bolt through the hole in the wall mounting plate and into the hole in the wall
so that the arms of the split-wing toggle are horizontal.
For the correct hole size, refer to the instructions for the particular split-wing toggles
used.

After the arms expand, pull the wall mounting plate out until the arms of the split-wing
toggle grip firmly into the wall.

Tighten the bolt until the wall mounting plate is securely fixed into the wall.

Insert the wood screw through the hole in the wall mounting plate and tighten until the
wall mounting plate is securely fixed to the wall.
For the correct hole size, refer to the instructions for the particular wood screws used.