Panasonic KV-SS905C Service Manual ▷ View online
9.6.2.8.
Mode - 8
Select a menu of Setting Item by
pushing “
pushing “
” or “
” key.
8
Push STOP/START key once.
9
(From Section 9.6)
(To Section 9.6)
Push HOME key once.
(13) Sleep Mode
Enter in Sleep Mode.
End the Sleep Mode.
93
KV-SS905C
9.6.3.
Error Code
Error Code Outline
ST1
Error contents
0×
Communication error
1×
Paper jam error
2×
Door open error
3×
Mechanical function error
4×
Paper (Document) sensor error
5×
Scanning error
6×
-
7×
-
8×
Hardware error
9×
Hardware error
A×
Hardware error
B×
-
C×
-
D×
-
E×
-
F×
-
Table 9-1
Error code outline
Contents
Contents
Contents
U1×
Document
H1×
F1×
Hardware
U2×
Document
H2×
F2×
Hardware
U3×
Door
H3×
F3!×
Hardware
U4×
Other
H4×
Lamp
F4×
Mechanical issue
U5×
H5×
F5×
Sensor
U6×
H6×
F6×
Scanning
U7×
H7×
F7×
Sensor
U8×
H8×
F8×
U9×
H9×
F9×
Hardware
Table 9-2
Classified
Code
ST1
ST2
ST3
ST4
Contents
U10
10
00
00
00
No paper error
U11
11
×
00
00
Paper Feed Jam : ST2shows the rest numbers (approx.) of paper.
U12
12
×
00
00
Jam1 (around conveyor) : ST2 shows the rest numbers (approx.) of paper.
U13
13
×
00
00
Jam2 (around conveyor) : ST2 shows the rest numbers (approx.) of paper.
U14
14
×
00
00
Jam3 (around conveyor) : ST2 shows the rest numbers (approx.) of paper.
U15
15
×
00
00
Jam4 (around conveyor) : ST2 shows the rest numbers (approx.) of paper.
U16
16
×
00
00
Jam1 (around Exit Roller) : ST2 shows the rest numbers (approx.) of paper.
U17
17
×
00
00
Jam2 (around Exit Roller) : ST2 shows the rest numbers (approx.) of paper.
U18
18
×
00
00
Paper remain in scanner *(ST2 : Paper position information)
U14
14
FF
×
×
Overrun error : ST2 shows the rest numbers (approx.) of paper.
U20
19
00
00
00
Skew error
U23
1C
×
×
00
Double feed error (ST2 : Sensor information)
(ST3:0=Document at Waiting Sensor
1=No document at Waiting Sensor 2=Length 3=Supersonic frequency)
(ST3:0=Document at Waiting Sensor
1=No document at Waiting Sensor 2=Length 3=Supersonic frequency)
U30
20
00
00
00
Front door open
U31
21
00
00
00
Back door open
U32
22
00
00
00
Post imprinter door open
U33
23
00
00
00
Lamp door open
F40
30
00
00
00
Hopper drive (Lower) error
U41
58
00
00
00
Scanning position adjustment error
F42
32
00
00
00
Hopper drive (Upper) error
F50
40
00
00
00
Waiting sensor error
F51
41
00
00
00
Starting position sensor error
F52
42
00
00
00
Skew (R) sensor error
F53
43
00
00
00
Skew (L) sensor error
F54
44
00
00
00
Paper jam sensor error
F55
45
00
00
00
Ending (front) position sensor error
F56
46
00
00
00
Ending (rear) position sensor error
F57
48
00
00
00
Edge Limit (R) sensor error
F58
49
00
00
00
Edge Limit (L) sensor error
F70
47
×
00
00
Size sensor error (ST2 : Information for exit tray guide’s position)
F60
50
00
00
00
Front side gain error
94
KV-SS905C
Classified
Code
ST1
ST2
ST3
ST4
Contents
F62
52
00
00
00
Back side gain error
H40
54
×
×
00
Front side lamp lighting error (ST2 : Lighting value ST3 : AD input level)
H41
55
×
×
00
Back side lamp lighting error (ST2 : Lighting value ST3 : AD input level)
F80
60
×
×
00
Double feed sensor error (ST2 : Output level ST3 : Input level)
F10
80
00
00
00
Program ROM (on MAIN Board) error
F11
81
×
×
×
Work RAM (on MAIN Board) error (ST2 : Data ST3,4 : Address)
F13
83
00
00
00
SCSI Program ROM (on I/F Board) error
F14
84
×
×
×
Work RAM (on I/F Board) error (ST2 : Data ST3,4 : Address)
F17
87
00
00
00
SO DIMM error
F18
88
00
00
00
DIMM error
F20
8A
×
×
×
Front side shading RAM error (ST2 : Data ST3,4 : Address)
F21
8B
×
×
×
Front side line RAM error (ST2 : Data ST3,4 : Address)
F22
8C
×
×
×
Front side color MTF RAM error (ST2 : Data ST3,4 : Address)
F28
92
×
×
×
Rotation RAM error (ST2 : Data ST3,4 : Address)
F32
96
×
×
×
SCSI buffer A error (ST2 : Data ST3,4 : Address)
F33
97
×
×
×
SCSI buffer B error (ST2 : Data ST3,4 : Address)
F34
98
00
00
00
EEPROM error
F35
99
00
00
00
GA-IF error
F36
9A
00
00
00
Front side GA-SEN error
F37
9B
00
00
00
GA-IMG error
F38
9C
00
00
00
Back side GA-SEN error
F90
AA
×
×
×
Back side shading RAM error (ST2 : Data ST3,4 : Address)
F91
AB
×
×
×
Back side line RAM error (ST2 : Data ST3,4 : Address)
F92
AC
×
×
×
Back side color MTF RAM error (ST2 : Data ST3,4 : Address)
Note
U18 Paper Position Information
95
KV-SS905C
10 TROUBLE SHOOTING
10.1. Warning
Warning message on LCD
Possible Cause
Check point
The rollers are dirty.
Clean the rollers.
The rollers need to be replaced.
Replace the paper feed roller module
and retard roller module.
and retard roller module.
10.2. Error Code
Classified Code
Error Code
Possible Cause
Check point
U10
No paper error
No paper error
10 00 00 00
The document is not loaded on the hopper
properly.
properly.
Load the document correctly.
The sensor cannot detect the document as it is
curled.
curled.
Straighten the document and load it again.
Paper Detector does not work properly.
Execute Document Sensor according to 9.6.2.3
and check “P” status.
and check “P” status.
U11
Paper feed jam
Paper feed jam
11 ×× 00 00
The document is jammed.
Open the front door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Waiting Sensor does not work properly.
Execute Document Sensor according to 9.6.2.3
and check "W" status.
and check "W" status.
U12
Jam 1 (around conveyor)
Jam 1 (around conveyor)
12 ×× 00 00
The document is jammed.
Open the front door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Starting Position Sensor does not work properly. Execute Document Sensor according to 9.6.2.3
and check "S" status.
U13
Jam 2 (around conveyor)
Jam 2 (around conveyor)
13 ×× 00 00
The document is jammed.
Open the back door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Paper Jam Sensor or Pointer Detector does not
work properly.
work properly.
1. Paper Jam senor
Execute Document Sensor according to
9.6.2.3 and check "J" status.
9.6.2.3 and check "J" status.
2. Pointer Detector
Execute Door & Home Sensor according to
9.6.2.3 and check "P" status.
9.6.2.3 and check "P" status.
U14
Jam 3 (around conveyor)
Jam 3 (around conveyor)
14 ×× 00 00
The document is jammed.
Open the front door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Exit [Front] sensor does not work properly.
Execute Document Sensor according to 9.6.2.3
and check "E" status.
and check "E" status.
U15
Jam 4 (around conveyor)
Jam 4 (around conveyor)
15 ×× 00 00
The document is jammed.
Open the back door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Exit [Rear] sensor or Pointer Detector does not
work properly.
work properly.
1. Exit [Rear] sensor
Execute Document Sensor according to
9.6.2.3 and check "e" status.
9.6.2.3 and check "e" status.
2. Pointer Detector
Execute Door & Home Sensor according to
9.6.2.3 and check "P" status.
9.6.2.3 and check "P" status.
U16
Jam 1 (around Exit roller)
Jam 1 (around Exit roller)
16 ×× 00 00
The document is jammed.
Open the front door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Exit [Front] sensor does not work properly.
Execute Document Sensor according to 9.6.2.3
and check "E" status.
and check "E" status.
U17
Jam 2 (around Exit roller)
Jam 2 (around Exit roller)
17 ×× 00 00
The document is jammed.
Open the back door and remove the jammed
paper. Then clean all of the rollers.
paper. Then clean all of the rollers.
The paper sensor is dirty.
Clean the paper sensor.
Exit [Rear] sensor does not work properly.
Execute Document Sensor according to 9.6.2.3
and check "e" status.
and check "e" status.
96
KV-SS905C
Click on the first or last page to see other KV-SS905C service manuals if exist.