Panasonic KV-SS905C Service Manual ▷ View online
9.6.2.3.
Mode - 3
Select Sensor Test ((4) or (5) or (6) or (12) or (13))
((4) or (5) or (6) or (12) or (13))
Execute Sensor Test
Execute Sensor Test
(4)
Document Sensor
(Check each document
sensor condition.)
(Check each document
sensor condition.)
(5)
Sensor Sensitive Level
(6)
Door & Home Sensor
(12)-a Memory Test (MAIN)
(12)-b Memory Test (SCSI)
(12)-c Memory Test (SO DIMM)
(12)-d Memory Test (DIMM)
(12)-b Memory Test (SCSI)
(12)-c Memory Test (SO DIMM)
(12)-d Memory Test (DIMM)
Select a menu of Setting Item by
pushing “
pushing “
” or “
” key.
Push HOME key once.
8
Test again?
or
Do another Test?
Push STOP/START key once.
Confirm the Test result.
Push STOP/START key.
9
No
Yes
(From Section 9.6)
(To Section 9.6)
P W L
R S
J
E
e
l
r
1
2
3
4
5
1
0
1
0
1
1
0
1
0
0
0
0
0
0
0
(4)
F
B
T
L
H
B
P
R
0
0
0
1
0
0
0
1
(6)
(12) : No Error or Error Message
P : Status of Paper Detector
W : Status of Waiting Sensor
L : Status of Skew [L] Sensor
R : Status of Skew [R] Sensor
S : Status of Starting Position Sensor
J : Status of Paper Jam Sensor
E : Status of Exit [Front] Sensor
e : Status of Exit [Rear] Sensor
l
W : Status of Waiting Sensor
L : Status of Skew [L] Sensor
R : Status of Skew [R] Sensor
S : Status of Starting Position Sensor
J : Status of Paper Jam Sensor
E : Status of Exit [Front] Sensor
e : Status of Exit [Rear] Sensor
l
: Status of Edge Limit [L] Sensor
r
: Status of Edge Limit [R] Sensor
∗
When this status value is “1”, it means the paper is in this scanner.
P W L
R S
J
E
e
l
r
1
2
3
4
5
x
3
3
3
3
3
3
4
3
3
x
x
x
x
x
(5)
P, 1, 2, 3, 4, 5, : (X:No range) : Neglect this information.
W : Status of Waiting Sensor : Range 0-F (F:Darker)
L : Status of Skew [L] Sensor : Range 0-F (F:Darker)
R : Status of Skew [R] Sensor : Range 0-F (F:Darker)
S : Status of Starting Position Sensor : Range 0-F (F:Darker)
J : Status of Paper Jam Sensor : Range 0-F (F:Darker)
E : Status of Exit [Front] Sensor : Range 0-F (F:Darker)
e : Status of Exit [Rear] Sensor : Range 0-F (F:Darker)
l
W : Status of Waiting Sensor : Range 0-F (F:Darker)
L : Status of Skew [L] Sensor : Range 0-F (F:Darker)
R : Status of Skew [R] Sensor : Range 0-F (F:Darker)
S : Status of Starting Position Sensor : Range 0-F (F:Darker)
J : Status of Paper Jam Sensor : Range 0-F (F:Darker)
E : Status of Exit [Front] Sensor : Range 0-F (F:Darker)
e : Status of Exit [Rear] Sensor : Range 0-F (F:Darker)
l
: Status of Edge Limit [L] Sensor : Range 0-F (F:Darker)
r
: Status of Edge Limit [R] Sensor : Range 0-F (F:Darker)
F : Status of Front Door
B : Status of Back Door
T : Status of Post Imprinter Door
L : Status of Lamp Door
B : Status of Back Door
T : Status of Post Imprinter Door
L : Status of Lamp Door
H : Status of Hopper Sensor (Upper) position (Value "1" : Upper position)
B : Status of Hopper Sensor (Lower) position (Value "1" : Lower position)
B : Status of Hopper Sensor (Lower) position (Value "1" : Lower position)
P : Status of Pointer Detector (Value "0" means straight-pass mode.)
R : Status of Retard Roller Position (Value "1" means Retard position is released)
R : Status of Retard Roller Position (Value "1" means Retard position is released)
Note
∗
Each sensor position
Refer to see. 5.3
A3
B4
B5
A5
B6
BC
A6
A4
(letter)
1
2
3
4
0
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
0
0
0
0
5
0
0
0
0
0
0
0
0
1
1
Front Door (F)
Post Imprinter Door (T)
Lamp Door (L)
F
B
T
L
1
1
0
1
0
0
1
0
0
0
0
1
0
1
0
1
Back Door (B)
Door name to open
89
KV-SS905C
9.6.2.4.
Mode - 4
Select a menu of Setting Item by
pushing " " or " " key.
pushing " " or " " key.
8
Push STOP/START key once.
Push HOME key once.
Test again?
or
Do another Test?
9
No
Yes
(From Section 9.6)
(To Section 9.6)
Push STOP/START key once.
Push STOP/START key once.
Confirm the Test result.
∗
(7) Hopper
Test
∗
(8)
Conveyor Motor
∗
(9)
Feed Motor
(10) Aging
∗
The test will be repeated continuously
until STOP/START key is pressed
90
KV-SS905C
9.6.2.5.
Mode - 5
Select a menu of Setting Item by
pushing “
pushing “
” or “
” key.
8
Set Test chart on Scanner
Confirm the Test result.
Push STOP/START key
Push HOME key once.
Test again?
or
Do another Test?
9
Yes
No
(From Section 9.6)
(To Section 9
.
6)
Push STOP/START key once.
(16) Adjust Double Feed Detector
(17) Adjust Length automatically
(18) Adjust Front V. Position automatically
(19) Adjust Front Width automatically
(20) Adjust Front H. Position automatically
(21) Adjust Back V. Position automatically
(22) Adjust Back Width automatically
(23) Adjust Back H. Position automatically
(24) Adjust All Position & Length automatically
(25) Adjust Shading
Note:
(17) Adjust Length automatically
(18) Adjust Front V. Position automatically
(19) Adjust Front Width automatically
(20) Adjust Front H. Position automatically
(21) Adjust Back V. Position automatically
(22) Adjust Back Width automatically
(23) Adjust Back H. Position automatically
(24) Adjust All Position & Length automatically
(25) Adjust Shading
Note:
1. Before adjusting shading, be sure to clean the scanning glasses, reference plate, rollers, and sensors shown on Sec 7.2. to 7.4..
2. Before adjusting shading, be sure to check both Reference Plates (Front and Back) face to the white sides.
2. Before adjusting shading, be sure to check both Reference Plates (Front and Back) face to the white sides.
(In case of the black sides, turn the Reference Plates according to 6.7..)
(16):
Set Adjustment paper.
(Part No.: PBQX90121Z-J)
(Part No.: PBQX90121Z-J)
(17) - (24)
: Set Test chart A.
(Part No.: PBQX90095Z-J)
(17)
: Front Side
(18)
: Front Side ("Set 2pcs of
Test chart on account of
including adjustment for
the function of "Sensor
Delay automatically")
Test chart on account of
including adjustment for
the function of "Sensor
Delay automatically")
(19), (20)
: Front Side
(21), (22), (23) : Back Side
(24)
(24)
: Set 8 charts in following order
(25):
Set Shading paper.
(Part No.: PBQX90113Z-J)
(Part No.: PBQX90113Z-J)
Note: When the following message indicates
on LCD during executing "Adjust Shading",
turn the Reference Plates (Front and Back)
to the black sides.
turn the Reference Plates (Front and Back)
to the black sides.
No Error
or
Error Message
or
Error Message
Turn Plate
Front: W B Black: W B
Front: W B Black: W B
Front Side
Front Side
Front Side
Front Side
Front Side
Back Side
Back Side
Back Side
Front Side
Front Side
Front Side
Front Side
Back Side
Back Side
Back Side
91
KV-SS905C
9.6.2.6.
Mode - 6
Select a menu of Setting Item by
pushing " " or " " key.
pushing " " or " " key.
Push HOME key once.
8
9
(14) Init. EEPROM
∗
Please be very careful, as this
test operation initializes all data.
Note:
Note:
Only perform "Init. EEPROM"
when EEPROM Error (F34) occurs.
When "Init. EEPROM" is executed,
all adjustments in Service Mode 1
and Service Mode 2 need to be
confirmed.
when EEPROM Error (F34) occurs.
When "Init. EEPROM" is executed,
all adjustments in Service Mode 1
and Service Mode 2 need to be
confirmed.
Push "
" and "
" keys once at
the same time.
Confirm the Test result.
Push STOP/START key once.
Execute initializing EEPROM.
Test again?
or
Do another Test?
Yes
No
(From Section 9.6)
(To Section 9.6)
9.6.2.7.
Mode - 7
Select a menu of Setting Item by
pushing “
pushing “
” or “
” key.
Push HOME key once.
8
9
Confirm the DIMM information by
pushing “
pushing “
” or “
” key.
Yes
No
(From Section 9.6)
(To Section 9.6)
(11) DIMM SPD (Serial Presence
Detect) Information
a. SO DIMM SPD (Information)
b. DIMM SPD (Information)
b. DIMM SPD (Information)
Execute another item?
(11) - a
(11) - b
11. DIMM SPD
Byte xx Value xx
Byte xx Value xx
11. SO DIMM SPD
Byte xx Value xx
Byte xx Value xx
92
KV-SS905C
Click on the first or last page to see other KV-SS905C service manuals if exist.