Panasonic KV-SL3066 / KV-SL3056 / KV-SL3055 / KV-SL3036 / KV-SL3035 Service Manual ▷ View online
41
8.4.7.
Exit Roller
(1) Remove the Side Plate Assembly
(See 8.4.5. Side Plate
Assembly)
and the Conveyor Belt 2.
(2) Pull and remove the Pulley of the Exit Roller (arrow
2
), while
unlocking the hook (arrow
1
) on the Pulley.
Reassembling Note:
After reassembling the Pulley, be sure to check that the
Pulley is locked to the Exit Roller by pulling the Pulley.
Pulley is locked to the Exit Roller by pulling the Pulley.
(3) Slide and remove the Bearing from the Exit Roller (arrow
3
).
(4) Unlock the hook of the Conveyor Roller Bearing (arrow
4
).
(5) Unlock the Exit Roller by turning the Conveyor Roller
Bearing (arrow
5
).
(6) Slide the Exit Roller with the Conveyor Roller Bearing and
remove it (arrow
6
).
(7) Remove the Support Bearing.
(8) Remove the Polyslider.
(9) Remove the Conveyor Roller Bearing from the Exit Roller.
(9) Remove the Conveyor Roller Bearing from the Exit Roller.
Bearing
Exit Roller
Pulley
1
2
3
Hook
4
5
Exit Roller
Conveyor Roller Bearing
Support Bearing
Exit Roller
6
Conveyor Roller Bearing
Polyslider
Support Bearing
42
8.5.
Lower Chassis 2
8.5.1.
Bottom Plate
8.5.2.
Platen Motor
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Remove the screw A and the USB Earth Plate.
(3) Remove the 7 screws C.
(4) Remove the 2 screws F.
(5) Tilt the Bottom Plate and remove it from the hole.
(3) Remove the 7 screws C.
(4) Remove the 2 screws F.
(5) Tilt the Bottom Plate and remove it from the hole.
Reassembling Note:
Install the Bottom Plate with screws C and F first and then
install the USB Earth Plate with screw A.
Otherwise the USB Earth Plate may not contact with the
USB jack on the Control Board correctly.
install the USB Earth Plate with screw A.
Otherwise the USB Earth Plate may not contact with the
USB jack on the Control Board correctly.
While slanting the Bottom Plate, insert it into the hole.
(1) Remove the Bottom Plate.
(See 8.5.1. Bottom Plate)
(2) Remove the CONTROL Board.
(See 8.5.5. CONTROL Board)
(3) Remove the Polyslider and Gear.
(4) Remove the screw C.
(5) Remove the Platen Motor with Motor Plate.
(6) Remove the 2 screws G and remove the Platen Motor from
(4) Remove the screw C.
(5) Remove the Platen Motor with Motor Plate.
(6) Remove the 2 screws G and remove the Platen Motor from
the plate.
(7) Disconnect the connector.
Hole
Bottom Plate
Bottom Plate
F
A
USB Earth Plate
Bottom Plate
Bottom Plate
C
FFC
Harness
Hole
CONTROL Board
C
G
Platen Motor
Motor Plate
G
Gear
Polyslider
Connector
43
8.5.3.
FAN
8.5.4.
Power Supply
8.5.5.
CONTROL Board
8.5.6.
Conveyor Motor
8.5.7.
STARTING SENSOR Board
(1) Remove the Bottom Plate.
(See 8.5.1. Bottom Plate)
(2) Remove 2 screws E.
(3) Disconnect the connector on the CONTROL Board.
(4) Remove the FAN.
(3) Disconnect the connector on the CONTROL Board.
(4) Remove the FAN.
(1) Remove the Bottom Plate.
(See 8.5.1. Bottom Plate)
(2) Remove the 2 screws C.
(3) Remove the Power Supply.
(4) Disconnect the connector from the CONTROL Board on the
(3) Remove the Power Supply.
(4) Disconnect the connector from the CONTROL Board on the
Power Supply.
(1) Remove the Bottom Plate.
(See 8.5.1. Bottom Plate)
(2) Disconnect all connectors (8 cable connectors and 5 FFC
cables) to CONTROL Board.
(3) Remove the CONTROL Board.
Power Supply
FAN
C
E
CONTROL Board
FFC
Harness
(1) Remove the CONTROL Board.
(See 8.5.5. CONTROL Board)
(2) Remove the Side Plate Assembly.
(See 8.4.5. Side Plate
Assembly)
(3) Remove the 2 screws A.
(4) Remove the connector and remove Conveyor Motor.
(4) Remove the connector and remove Conveyor Motor.
(1) Remove the CONTROL Board.
(See 8.5.5. CONTROL Board)
(2) Remove the 3 screws C.
(3) Remove the STARTING SENSOR Board Assembly.
(4) Remove the screw C, disconnect the connector.
(5) Remove the STARTING SENSOR Board.
(3) Remove the STARTING SENSOR Board Assembly.
(4) Remove the screw C, disconnect the connector.
(5) Remove the STARTING SENSOR Board.
Conveyor Motor
A
STARTING SENSOR
Board Assembly
Board Assembly
C
C
STARTING SENSOR Board
Connector
44
8.5.8.
Wiring of Lower Chassis
Click on the first or last page to see other KV-SL3066 / KV-SL3056 / KV-SL3055 / KV-SL3036 / KV-SL3035 service manuals if exist.