Panasonic KV-SL1066-M2 / KV-SL1066-U2 / KV-SL1066-B2 / KV-SL1066-K2 / KV-SL1066-C2 / KV-SL1066-CH / KV-SL1056-M2 / KV-SL1056-U2 / KV-SL1055-C2 / KV-SL1055-CH / KV-SL1036-C2 / KV-SL1055-CH / KV-SL1035-C2 / KV-SL1055-CH Service Manual ▷ View online
11
4 Location of Controls and Components
4.1.
Main Unit
Front
1
2
3
5
4
6
7
8
9
10
11
12
14
13
Document guides
Mixed batch card guide
When the unit is shipped, this is stored in the feed tray.
For details, see Operating Manual "Mixed Batch Card Guide (ADF)".
For details, see Operating Manual "Mixed Batch Card Guide (ADF)".
Manual feed selector
You can select the document feeding method.
: Manual feeding
: Automatic feeding
: Automatic feeding
Operation panel
For details, refer to Operating Manual "Operation Panel".
Exit tray
Exit extension tray 1
Exit extension tray 2
Exit stopper
Exit guides
Fan exhaust vent
ADF door
ADF door release
: Push to open the ADF door.
Feed tray
: Load the documents with the surface to be scanned facing down.
: Make sure to remove paper clips and staples from documents.
Feed extension tray
12
Rear
Security slot
Use a commercially available security cable.
USB connector
USB cable
Connect the USB cable to the scanner and the other end of the USB cable to the computer.
Power cord
Use a commercially available security cable.
USB connector
USB cable
Connect the USB cable to the scanner and the other end of the USB cable to the computer.
Power cord
1
2
3
4
5
AC inlet (M2/U2/B2/K2)
13
4.2.
Operation Panel
1
2
3
5
4
6
7
LED (Red)
Lights when an error occurs.
LED (Green)
Shows the scanner’s status.
Power button ( )
For details, see Operating Manual "Turning ON/OFF the unit's power".
Cursor button
Skip button (
)
If you press this button after a double feed is detected and scanning has been paused, the document (or
documents) detected as a double feed will be scanned, and then ejected from the scanner. Scanning will
continue after the document is scanned and ejected.
documents) detected as a double feed will be scanned, and then ejected from the scanner. Scanning will
continue after the document is scanned and ejected.
Start/Stop button (
)
•
If you set [Wait Key] for "Manual Feed Mode" in your application software, pushing this button starts
scanning. For details about "Manual Feed Mode", refer to the Image Capture Plus, TWAIN, or ISIS
help.
scanning. For details about "Manual Feed Mode", refer to the Image Capture Plus, TWAIN, or ISIS
help.
•
During scanning, pushing this button stops scanning.
•
If you press this button after a double feed is detected and scanning has been paused, the document
(or documents) detected as a double feed will be ejected from the scanner without being scanned.
Scanning will stop.
(or documents) detected as a double feed will be ejected from the scanner without being scanned.
Scanning will stop.
7-segment LED
If you are using the scanner with Image Capture Plus, you can perform a push scan using the 7-
segment LED. A registered job number is displayed on the 7-segment LED. Use the cursor button (
segment LED. A registered job number is displayed on the 7-segment LED. Use the cursor button (
)
to select a job.
14
4.2.1.
About LED
The status of the scanner is displayed by the LED (Red) (
) and the LED (Green) (
), as shown in the
table below:
LED (Red)
LED (Green)
Status
OFF
OFF
Power OFF
*1
OFF
ON
Ready mode or Scanning
OFF
Blinking (Fast)
Warming up
OFF
Blinking (Fast, 2 times consecutively)
Double Feed Skip mode
OFF
Blinking (Fast, 3 times consecutively)
Dog-ear detection skip mode
OFF
Blinking (Slow)
Sleep mode
*2
or Cleaning mode
Blinking (Slow)
Blinking (Slow)
Sleep mode
*2
and Notification mode
Blinking (Slow)
ON
Notification mode
ON
OFF
Error
*3
*1
If the power off feature in sleep mode is enabled, and if no operation is performed for a certain period of time, the scanner will be
turned off automatically. Press the power button (
turned off automatically. Press the power button (
) of the scanner to turn it on. You can enable/disable the power off feature, and
change the time until the scanner turns off in User Utility.
*2
If no operation is performed for 15 minutes or longer, the scanner will enter sleep mode automatically to conserve energy. Press
any button (except the power button) on the scanner’s operation panel to return to ready mode. The time until the scanner enters
sleep mode can be changed in User Utility.
any button (except the power button) on the scanner’s operation panel to return to ready mode. The time until the scanner enters
sleep mode can be changed in User Utility.
*3
For details about the error, check in User Utility.
Click on the first or last page to see other KV-SL1066-M2 / KV-SL1066-U2 / KV-SL1066-B2 / KV-SL1066-K2 / KV-SL1066-C2 / KV-SL1066-CH / KV-SL1056-M2 / KV-SL1056-U2 / KV-SL1055-C2 / KV-SL1055-CH / KV-SL1036-C2 / KV-SL1055-CH / KV-SL1035-C2 / KV-SL1055-CH service manuals if exist.