Panasonic KV-S1026C / KV-S1015C (serv.man2) Service Manual ▷ View online
61
9.3.7.
Adjustment
Item
Operation
Default
Remarks
Shading
1. Click “Shading” on the main menu.
2. Clean the conveyor, rollers, and scanning glass section
according to the message on the display.
Then click “OK”.
3. Set the resolution (300 dpi, 600 dpi, 600dpi, and/or 600 dpi
Gray).
4. Set the Shading Sheet (Part No.: See 14.5.) on the Feed
Tray in portrait orientation.
5. Click “OK” to start the shading correction.
6. Confirm the result.
7. Click “OK” to return to the main menu.
2. Clean the conveyor, rollers, and scanning glass section
according to the message on the display.
Then click “OK”.
3. Set the resolution (300 dpi, 600 dpi, 600dpi, and/or 600 dpi
Gray).
4. Set the Shading Sheet (Part No.: See 14.5.) on the Feed
Tray in portrait orientation.
5. Click “OK” to start the shading correction.
6. Confirm the result.
7. Click “OK” to return to the main menu.
—
Until this process is
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
All Position
1. Set 2 pcs of Test Chart A4 (Part No.: See 14.5.) on the
Feed Tray in portrait orientation.
2. Click “All position” on the main menu to execute scanning
position, length, and paper-end adjustment.
3. Check the result.
4. Click “OK” to return to the main menu.
Feed Tray in portrait orientation.
2. Click “All position” on the main menu to execute scanning
position, length, and paper-end adjustment.
3. Check the result.
4. Click “OK” to return to the main menu.
—
Set 2 pcs of Test Chart A4 on
the Feed Tray in the
following order:
the Feed Tray in the
following order:
1st page: Front side
2nd page: Back side
2nd page: Back side
Individual Position 1. Adjust Automatically.
a. Set Test Chart A4 (Part No.: See 14.5.) on the Feed Tray
in portrait orientation.
b. Click “Individual Position” on the main menu.
c. Click one of 6 “Adjust Automatically” buttons on the
“Individual Position” dialog box to execute the
adjustment.
d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” to return to the main menu.
in portrait orientation.
b. Click “Individual Position” on the main menu.
c. Click one of 6 “Adjust Automatically” buttons on the
“Individual Position” dialog box to execute the
adjustment.
d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” to return to the main menu.
2. Adjust Manually.
a. Click “Individual Position” on the main menu.
b. Change the parameters (mm, %) on the “Individual
Position” dialog box as required. (Refer to Remarks.)
c. Click “OK” to renew the setting, and to return to the
main menu.
a. Click “Individual Position” on the main menu.
b. Change the parameters (mm, %) on the “Individual
Position” dialog box as required. (Refer to Remarks.)
c. Click “OK” to renew the setting, and to return to the
main menu.
—
1. Adjust Automatically
(6 adjustments)
a. Length
b. Paper End Position
c. Front V. Position
d. Front H. Position
e. Back V. Position
f. Back H. Position
(6 adjustments)
a. Length
b. Paper End Position
c. Front V. Position
d. Front H. Position
e. Back V. Position
f. Back H. Position
2. Adjust Manually
(Length)
+: Increasing the number
makes the scanning
document length shorter.
(Paper End Position)
+: On the LC (Length
Control) mode, increasing
the number allows the
paper-end timing to be
earlier.
(Vertical Position)
+: Increasing the number
makes the document
scanning position shifted
upward.
(Horizontal Position)
+: Increasing the number
makes the document
scanning position shifted
to the left.
Note:
(Length)
+: Increasing the number
makes the scanning
document length shorter.
(Paper End Position)
+: On the LC (Length
Control) mode, increasing
the number allows the
paper-end timing to be
earlier.
(Vertical Position)
+: Increasing the number
makes the document
scanning position shifted
upward.
(Horizontal Position)
+: Increasing the number
makes the document
scanning position shifted
to the left.
Note:
If the appropriate
scanning position can
not be obtained by any
of the manual
adjustments, check the
CIS installation.
scanning position can
not be obtained by any
of the manual
adjustments, check the
CIS installation.
62
9.3.8.
Other
1. Click “Save Info” on the main menu to save the scanner and PC information as text files.
2. Click “Download the latest version” to open the site for Panasonic scanner products that provides the scanner software to be
2. Click “Download the latest version” to open the site for Panasonic scanner products that provides the scanner software to be
downloaded.
3. Click “Save Log” to open “Save As” dialog-box.
Then after renaming a log file, perform “Save” to save it.
Double Feed
1. Adjust Automatically.
a. Set the Shading Sheet (Part No.: See 14.5.) on the
Feed Tray in portrait orientation, sliding the Document
Guides so that they match the document width.
b. Click “Double Feed” in the “Adjust” section on the main
menu.
c. Click “Adjust Automatically” on the “Double Feed
Sensor” dialog box to adjust the double feed sensitivity.
d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” on the “Double Feed Detector” dialog box to
return to the main menu.
a. Set the Shading Sheet (Part No.: See 14.5.) on the
Feed Tray in portrait orientation, sliding the Document
Guides so that they match the document width.
b. Click “Double Feed” in the “Adjust” section on the main
menu.
c. Click “Adjust Automatically” on the “Double Feed
Sensor” dialog box to adjust the double feed sensitivity.
d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” on the “Double Feed Detector” dialog box to
return to the main menu.
2. Adjust Manually.
a. Click “Double Feed” in the “Adjust “ section on the main
menu.
b. Change the parameter (“Send Level”) on the “Double
Feed Detector” dialog box.
c. Click “OK” on the “Double Feed Detector” dialog box to
return to the main menu.
a. Click “Double Feed” in the “Adjust “ section on the main
menu.
b. Change the parameter (“Send Level”) on the “Double
Feed Detector” dialog box.
c. Click “OK” on the “Double Feed Detector” dialog box to
return to the main menu.
—
* USB ID
1. Click “USB ID” on the main menu to enter the “USB ID”
dialog box.
2. Click “Set” on the “USB ID” dialog box to store a new ID
number for a newly replaced CONTROL Board.
3. Click “Close” to return to the main menu.
dialog box.
2. Click “Set” on the “USB ID” dialog box to store a new ID
number for a newly replaced CONTROL Board.
3. Click “Close” to return to the main menu.
—
*This setting is available only
for a newly replaced
CONTROL Board (or IC28).
for a newly replaced
CONTROL Board (or IC28).
Item
Operation
Default
Remarks
63
9.4.
Scanner Self-test
Without connecting the scanner to the PC, the following scanner self-tests can be performed. The following mechanical tests are
generally used after replacing or reassembling rollers (Conveyor Roller, Exit Roller) and other mechanical parts related to
feeding documents.
Note:
generally used after replacing or reassembling rollers (Conveyor Roller, Exit Roller) and other mechanical parts related to
feeding documents.
Note:
*: For LEDs (Red, Green) position shown in the following figure, see Sec. 3.
**: It takes about 20 seconds until the LEDs change to match the status you want.
**: It takes about 20 seconds until the LEDs change to match the status you want.
Test Item
Operation
LED Status
Remarks
*
LED
(Red)
*
LED
(Green)
**1. Conveyor
Motor’s rotating
Motor’s rotating
1. While holding down “START/STOP Button”
on the Top Cover, push the “Power Button” to
turn on the scanner.
turn on the scanner.
—
—
2. Release the Buttons (“START/STOP Button”
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): ON / LED (Green): OFF)
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): ON / LED (Green): OFF)
ON
OFF
3. Push the “START/STOP Button” once to start
the test.
the test.
ON
OFF
4. Push the “START/STOP Button” once to stop
the test.
the test.
ON
OFF
5. Turn off the scanner to finish the test.
ON
OFF
**2. Feed
1. While holding down “START/STOP Button”
on the Top Cover, push the “Power Button” to
turn on the scanner.
turn on the scanner.
—
—
2. Release the Buttons (“START/STOP Button”
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): OFF / LED (Green): ON)
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): OFF / LED (Green): ON)
OFF
ON
3. Set documents on the Feed Tray.
OFF
ON
4. Push the “START/STOP Button” once to
start the test.
start the test.
OFF
ON
5. Push the “START/STOP Button” once to stop
the test.
the test.
OFF
ON
6. Turn off the scanner to finish the test.
—
—
**3. Shading
1. While holding down “START/STOP Button”
on the Top Cover, push the “Power Button” to
turn on the scanner.
turn on the scanner.
—
—
1. Before
executing the
shading function,
be sure to clean
the scanning
area, rollers, and
conveyors related
to conveying
documents
2. Until this
process is
completed, don’t
stop the process
by opening any
doors or turning
off the scanner.
executing the
shading function,
be sure to clean
the scanning
area, rollers, and
conveyors related
to conveying
documents
2. Until this
process is
completed, don’t
stop the process
by opening any
doors or turning
off the scanner.
2. Release the Buttons (“START/STOP Button”
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): OFF / LED (Green): OFF)
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): OFF / LED (Green): OFF)
OFF
OFF
3. Set a piece of Shading Sheet (Part No.: See
14.5.) on the Feed Tray in portrait orientation.
14.5.) on the Feed Tray in portrait orientation.
OFF
OFF
4. Hold down the “START/STOP Button” for 5
seconds or more to enter the shading test.
seconds or more to enter the shading test.
OFF
ON
5. Paper feeding starts to execute the shading.
OFF
ON
6. After confirming the LED (green) turns OFF,
turn off the scanner to finish the test.
turn off the scanner to finish the test.
OFF
OFF
64
Note
***
:
Every time you push the “START/STOP Button”, CIS ON/OFF status will change periodically, as follows:
CIS (F) OFF / CIS (B) OFF
CIS (F) OFF / CIS (B) OFF
→ CIS (F) ON / CIS (B) OFF → CIS (F) OFF / CIS (B) ON
→ CIS (F) ON / CIS (B) ON → CIS (F) OFF / CIS (B) OFF →.......
**4.CIS ON/ OFF
1. While holding down “START/STOP Button”
on the Top Cover, push the “Power Button” to
turn on the scanner.
turn on the scanner.
—
—
2. Release the Buttons (“START/STOP Button”
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): ON / LED (Green): ON)
and “Power Button”) when the LEDs change
to match the status in the right column.
(LED (Red): ON / LED (Green): ON)
ON
ON
3. Push the “START/STOP Button” once to
turn on the CIS (F). (See Note*** below.)
turn on the CIS (F). (See Note*** below.)
ON
ON
4. Push the “START/STOP Button” once to
turn on the CIS (B), and to turn off the
CIS (F).
turn on the CIS (B), and to turn off the
CIS (F).
ON
ON
5. Push the “START/STOP Button” once to
turn on the CIS (F) and CIS (B).
turn on the CIS (F) and CIS (B).
ON
ON
6. Push the “START/STOP Button” once to
turn off the CIS (F) and CIS (B).
turn off the CIS (F) and CIS (B).
ON
ON
7. Turn off the scanner to finish the test.
—
—
Test Item
Operation
LED Status
Remarks
*
LED
(Red)
*
LED
(Green)
Click on the first or last page to see other KV-S1026C / KV-S1015C (serv.man2) service manuals if exist.