DOWNLOAD Panasonic EP-MA70CX890 / EP-MA70KX890 Service Manual ↓ Size: 7.82 MB | Pages: 82 in PDF or view online for FREE

ORDER NO. HPD1102E25CE

 

-

 65 - 

9.8. Display of malfunction analysis-4 [C8] 

＊  If the display is 15 (Heater error). 

①: If you push OK, the Heater lights. 

②: When in the condition of  ①, 

1)  If you push the Wider switch, the Heater arm(CN101) is shown when the 

operation error occurred. 

2)  If you push the Narrower switch, the Heater arm(CN102) is shown when the 

operation error occurred. 

        Caution: If the temperature is more than 99℃, it is shown 99℃. 

 

 

Notes: 

      - The Sensor detects no change.

 Disconnection of Lead wires, Loose Connectors, or faulty Sensors 

      - The Sensor detects abnormal change.

 Partial disconnection of Lead wires, or faulty Sensors 

   - Sensor malfunction when the Switch is turned on.

 Any Rotation sensors are faulty. 

      ＊When the Position sensors are faulty, it is detected as ‘’No change’’.

 

 

ORDER NO. HPD1102E25CE

 

-

 66 - 

Check if the Massage mechanism block is properly assembled or there is nothing wrong with the Sensors 
or Motors.      ＊Detect failures in Sensors or Motors. 

1. Proceed the procedures of 9.1. Preparation of Secret Mode. 
2. Push the button of BACK INTENSITY till CA appears, and push the OK button. 
3. Massage mechanism block starts operating.    If there is nothing wrong, it stops normally. 
4.  If the operation stops halfway, push the buttons of Off/On or Stop on the Controller. 
 

1. Proceed the procedures of 9.1. Preparation of Secret Mode 

2. Push the button of BACK INTENSITY till CC appears, and push the OK button. Any of the following is 

shown. 

3. Push the OK button again. 

4. Push the Off/On button on the Controller.    The adjustment is done. 

ORDER NO. HPD1102E25CE

 

-

 67 - 

Check if the Heater increases its temperature properly by the list of the room temperature and its time 
till it reaches designated temperatures. 
(Our criterion is that the spot touching the human body is 50℃.    However, there is the balance 5℃ in 
the Heat sensor and the spot of the human body touching the Massage ball, therefore in the list 45℃ is 
used as criterion.) 

 

Caution: 

-  Carry out the checking with nobody sitting or without operation of the Massage mechanism 

block. 

-  Heater massage balls need to be cool enough (normal temperature). 
-  The balance between right/left Massage balls is within ±5℃.  If the values are within this 

range, it is not faulty. 

【Checking procedures】 

①  Start CE mode of the Secret Mode of the Controller. 

②  If you push the REPEAT button for several times,,,,,,,, 

    For example,  

        <CE> 

 Once <02>  Twice <05>  Thrice <2>  Fourth <4> 

    This means that one of Heal balls is 25℃ and the other is 24℃. If you push CD, it resumes to the 

beginning. 

        ＊You can know the original temperatures of the Massage balls. 

③  Push the button of HEAT OFF/ON and turn on the switch, and measure the time of the increase of the 

temperature. 

④  Repeat the procedures of  ②  and measure the time till 45℃ is shown. 

⑤  Check the Heater by the list.    For example, if the room temperature is 20℃ and 45℃ is shown within 

150 seconds, it can be judged ‘’Good’’. 

 

ORDER NO. HPD1102E25CE

 

-

 68 - 

1. Proceed the procedures of 9.1. Preparation of Secret Mode. 
2. Push the button of BACK INTENSITY till CE appears, and push the OK button. 
3. You can check each operations by pushing the following Switches. 
            ◆  Reclining switch (Back Up/down), Ottoman switch (Ottoman Up/down) 
            ◆  Position switch (Upward, downward, narrower, wider) 
            ◆  Back intensity (Strong, weak)  ◆  Heater (Off, on) 
          ◆  Manual (Neck, shoulder, middle back, lower back, full back, tap) 

●

  Checking the temperature of the Heater 

1. You can check the temperature of the Heater if you push the OK button after 9.12.2 then push the REPEAT 

button.    However, if the HEAT OFF/ON button is not pushed, the normal temperature is displayed. 

2.  To stop the operation, push the Off/on button or the stop button.