Panasonic NN-DF383BZPE Service Manual ▷ View online
• Remove the left side screw.
• Loose the right side screw.
• Loose the right side screw.
(NOTE: Do not take out the screw)
• Insert screwdriver into the gap (between hinge D and
right hinge U) to widen the space to release the Door E
hinge from right hinge U.
hinge from right hinge U.
To remove door C and door A
• Insert flat blade screwdriver to release hinge pin
from left hinge.
• Release catch hooks between door C and door A, to
detach the door C.
Release catch hooks.
NOTE:
After replacement of the defective component parts
of the door, reassemble it properly and adjustment
so as to prevent an excessive microwave leakage.
Adjustment of the door assembly(Refer page 23).
of the door, reassemble it properly and adjustment
so as to prevent an excessive microwave leakage.
Adjustment of the door assembly(Refer page 23).
3. When mounting the door to the oven, be sure to adjust the
door parallel to the cavity front plate by moving hinges back
or forward.
or forward.
4. Adjust so that the upper portion of the door will touch firmly
to the oven cavity front plate, without pushing the door.
If the door assembly is not mounted properly, microwave
power may leak from the clearance between the door and
oven.
If the door assembly is not mounted properly, microwave
power may leak from the clearance between the door and
oven.
5. Be sure the gap between left or right portion of door
assembly and cavity front plate will be 0.6±0.3mm.
6. Always perform the microwave leakage measurement test
after installation and adjustment of door assembly.
17
NN-DF383B
4.8. Stirrer motor
1. Remove the motor cover by breaking off at the 8 spots
indicated by arrows with a cutter or the like.
NOTE:
After removing the motor cover, be sure that cut
portions are properly trimmed or bent to the inside
so that no sharp edges will be exposed to outside.
portions are properly trimmed or bent to the inside
so that no sharp edges will be exposed to outside.
2. Disconnect 2 lead wires from stirrer motor terminals.
3. Remove 2 screws holding stirrer motor.
3. Remove 2 screws holding stirrer motor.
NOTE:
After reinstalling the new stirrer motor and
reconnecting the 2 lead wires, reinstall the motor
cover by rotating it around 180, tucking the 2 tabs
under the base in the 2 provided slots, then screw
the single tab to the base using a screw.
reconnecting the 2 lead wires, reinstall the motor
cover by rotating it around 180, tucking the 2 tabs
under the base in the 2 provided slots, then screw
the single tab to the base using a screw.
4.9. Lower Heater (Heater AU)
1. Remove left and right door key springs from door arm.
NOTE:
Support door before removing door springs.
2. Disconnect connector of power supply cord.
3. Turn over the microwave oven.
4. Remove 5 screws holding base plate on the bottom of oven
3. Turn over the microwave oven.
4. Remove 5 screws holding base plate on the bottom of oven
cavity.
5. Remove 4 screws holding left and right hinges.
NOTE:
Do not remove the two screws holding the left and
right hinges on the bottom of cavity front plate.
right hinges on the bottom of cavity front plate.
18
NN-DF383B
6. Remove 1 screw holding orifice on base plate.
7. Remove base plate from oven assy.
8. Remove 4 screws holding lower heater panel on the bottom
8. Remove 4 screws holding lower heater panel on the bottom
of oven cavity.
9. Release the catch hook holding orifice and then remove the
orifice.
10. Remove 2 screws holding lead wire terminals on lower
heaters.
11. Take away the whole lower heater assembly.
19
NN-DF383B
12. Remove the lower heater.
20
NN-DF383B
Click on the first or last page to see other NN-DF383BZPE service manuals if exist.