Panasonic UF-6300 / UF-6200 / UF-5300 Service Manual ▷ View online
45
(10) Remove 2 Pressure Springs (708).
(11) Remove the E14 Gear (714).
Caution:
You may need to use force to pull out the Gear.
(12) Remove the 2 E18 Gears (713).
(13) Remove 2 C-Rings (712).
(14) Remove the E24 Drive Gear (711).
(15) Remove 2 P17L6.8 Bushings (710).
(13) Remove 2 C-Rings (712).
(14) Remove the E24 Drive Gear (711).
(15) Remove 2 P17L6.8 Bushings (710).
(16) Remove the Fuser Roller (709).
Caution:
Do not scratch the surface of the Fuser Roller when
removing, or reinstalling it.
removing, or reinstalling it.
(17) Remove 1 Screw (4N).
(18) Remove the Lower Paper Exit Guide (703).
(18) Remove the Lower Paper Exit Guide (703).
(10)
(13)
(15)
(11)
(12)
(14)
(16)
(17)
(18)
46
2.2.16. Rear Chassis (505), SNS1 PC Board (1008)
(19) Remove 2 P6L5.5 Bushings (707).
(20) Remove the Pressure Roller (706).
(20) Remove the Pressure Roller (706).
Caution:
Do not scratch the surface of the Pressure Roller
when removing, or reinstalling it.
when removing, or reinstalling it.
(1) Remove the Power Supply Unit (Refer to 2.2.12.).
(2) Remove the SC PC Board (Refer to 2.2.12.).
(3) Remove the Fuser Unit (Refer to 2.2.14.).
(4) Remove 6 Screws (19).
(5) Remove the Bracket (403).
(6) Remove the Rear Chassis (505).
(2) Remove the SC PC Board (Refer to 2.2.12.).
(3) Remove the Fuser Unit (Refer to 2.2.14.).
(4) Remove 6 Screws (19).
(5) Remove the Bracket (403).
(6) Remove the Rear Chassis (505).
(7) Disconnect Connectors CN80, and CN81 on the
SNS1 PC Board (1008).
(8) Remove 1 Screw (19).
(9) Remove the SNS1 PC Board (1008).
(9) Remove the SNS1 PC Board (1008).
(19)
(20)
(4)
(4)
(5)
(6)
(9)
(8)
(7)
47
2.2.17. Transfer Guide (601) Assembly, Feed Roller (526)
(1) Remove the Rear Chassis (Refer to 2.2.16.).
(2) Remove 2 Screws (C8).
(3) Disconnect Connector CN80 on the SNS1 PC Board
(2) Remove 2 Screws (C8).
(3) Disconnect Connector CN80 on the SNS1 PC Board
(1008).
(4) Remove the Transfer Guide (601) Assembly.
(5) Remove the 2 Snap Rings. (B9).
(6) Remove the Feed Roller (526).
(6) Remove the Feed Roller (526).
(7) Remove the Roller Gear (529).
(8) Remove 2 P6L5 Bushings (527, 528).
(8) Remove 2 P6L5 Bushings (527, 528).
(2)
(2)
(4)
(3)
(2)
(5)
(6)
(7)
(8)
White
Black
48
2.2.18. Toner Sensor (513), Laser Unit [LSU] (512), SNS3 PC Board (1009)
(1) Remove the Transmit Guide Assembly
(Refer to 2.2.4.).
(2) Remove 2 Screws (19).
(3) Remove Ground Wire (542).
(4) Remove the CCD Shield Plate (533).
(3) Remove Ground Wire (542).
(4) Remove the CCD Shield Plate (533).
(5) Remove 1 Screw (19).
(6) Disconnect Connector CN84 on the SNS3 PC Board
(6) Disconnect Connector CN84 on the SNS3 PC Board
(1009).
(7) Remove the Toner Sensor Spring Plate (506)
Assembly.
Note:
When reinstalling, make sure that the Toner Sensor
Spring Plate is inserted into the 2 notches in the main
frame as illustrated.
Spring Plate is inserted into the 2 notches in the main
frame as illustrated.
(8) Remove the Toner Sensor (513).
(9) Disconnect the Connector on the Toner Sensor.
(9) Disconnect the Connector on the Toner Sensor.
(2)
(4)
(3)
(6)
(5)
(7)
(8)
(9)
Click on the first or last page to see other UF-6300 / UF-6200 / UF-5300 service manuals if exist.