Panasonic KX-FLC413UA Service Manual ▷ View online
45
KX-FLC413UA
6.12. Sensors and Switches Section
All of the sensor and switches are shown below.
Note:
See TEST FUNCTIONS - SENSOR CHECK SECTION for the sensor test.
(#815 of Service Mode test. Refer to Test Functions (P.88).
(#815 of Service Mode test. Refer to Test Functions (P.88).
6.12.1. Hook Switch
When the handset is raised, the switch is turned OFF, and the signal at pin 6 of IC101 is high.
When the handset is returned, the switch is turned ON, and the signal at pin 6 of IC101 is low.
When the handset is returned, the switch is turned ON, and the signal at pin 6 of IC101 is low.
6.12.2. Document Sensor
The Sensor detects whether or not a document is in place.
When a document is detected, the shelter plate shuts off the sensor light, the photo-transistor turns OFF, and the input signal of
IC101-19pin becomes a high level. When there is no document, the shelter plate let the sensor light pass through, the photo-
transistor turns ON, and the input signal of IC101-19pin becomes a low level.
When a document is detected, the shelter plate shuts off the sensor light, the photo-transistor turns OFF, and the input signal of
IC101-19pin becomes a high level. When there is no document, the shelter plate let the sensor light pass through, the photo-
transistor turns ON, and the input signal of IC101-19pin becomes a low level.
Sensor Circuit Location
Sensor
Sensor or Switch Name
Message Error
Operation Panel
PS101
Document set
[CHECK DOCUMENT]
Operation Panel
SW150
Paper Feed
[REMOVE DOCUMENT]
High Voltage PCB
SW1
Printer Open
[COVER OPEN]
High Voltage PCB
SW2
OPC Set
[CHECK DRUM]
Digital PCB
PS102
Regist
[FAILED PICKUP]
Digital PCB
PS101
Paper
[OUT OF PAPER]
Exit Sensor PCB
PS51
Exit
[PAPER JAMMED]
Toner Sensor PCB
IC60
Dev & Toner Set
[TONER EMPTY]
[TONER LOW]
[CHECK DRUM]
[TONER LOW]
[CHECK DRUM]
Operation Panel
SW151
Hook
————
Photo-transistor
Signal (IC101-19pin)
Document Set
OFF
High level
No Document
ON
Low level
46
KX-FLC413UA
6.12.3. Paper Feed Sensor
The Sensor detects the front edge of the document.
When a document is detected, the switch turns ON, and the input signal of IC107-74pin becomes a low level. When there is no doc-
ument, the switch turns OFF, and the input signal of IC107-74pin becomes a high level.
When a document is detected, the switch turns ON, and the input signal of IC107-74pin becomes a low level. When there is no doc-
ument, the switch turns OFF, and the input signal of IC107-74pin becomes a high level.
6.12.4. Top Cover Open Switch
The Switches detect whether the printer cover is open or closed.
When the printer cover is closed, the switches turn ON, and the input signal of IC107-37pin becomes a high level.
When the printer cover is open, the switches turns OFF, and the input signal of IC107-37pin becomes a low level.
When the printer cover is closed, the switches turn ON, and the input signal of IC107-37pin becomes a high level.
When the printer cover is open, the switches turns OFF, and the input signal of IC107-37pin becomes a low level.
Switch
Signal (IC107-74pin)
Read Position
ON
Low level
Non Read Position
OFF
High level
Switch
Signal (IC107-37 pin)
Open
OFF
High level
Close
ON
Low level
47
KX-FLC413UA
6.12.5. Drum Sensor
The Switch detects whether the OPC unit is set or not.
When there is the DRUM unit, the input signal of IC107-16pin becomes a low level.
When there is no DRUM unit, the input signal of IC107-16pin becomes a high level.
When there is the DRUM unit, the input signal of IC107-16pin becomes a low level.
When there is no DRUM unit, the input signal of IC107-16pin becomes a high level.
6.12.6. Regist Sensor
The Sensor detects whether or not the recording paper is present so that printing can start.
When the recording paper is detected, the shelter plate let the sensor light passing through, the photo-transistor turns ON, and the
input signal of IC107-5pin becomes a low level.
When there is no recording paper, the shelter plate closes the sensor light, the photo-transistor turns OFF, and the input signal of
IC107-5pin becomes a high level.
When the recording paper is detected, the shelter plate let the sensor light passing through, the photo-transistor turns ON, and the
input signal of IC107-5pin becomes a low level.
When there is no recording paper, the shelter plate closes the sensor light, the photo-transistor turns OFF, and the input signal of
IC107-5pin becomes a high level.
Signal (IC107-16 pin)
DRUM Set
Low level
No DRUM
High level
Photo-transistor
Signal (IC107-5 pin)
No Recording Paper
OFF
High level
Recording Paper Regist
ON
Low level
48
KX-FLC413UA
6.12.7. Paper Sensor..... "OUT OF PAPER"
The Sensor detects the recording paper are in place.
When the recording paper is detected, the shelter plate let the sensor light passing through, the photo-transistor turns ON, and the
input signal of IC107-35 pin becomes a low level.
When there is no recording paper, the shelter plate closes the sensor light, the photo-transistor turns OFF, and the input signal of
IC107-35 pin becomes a high level.
When the recording paper is detected, the shelter plate let the sensor light passing through, the photo-transistor turns ON, and the
input signal of IC107-35 pin becomes a low level.
When there is no recording paper, the shelter plate closes the sensor light, the photo-transistor turns OFF, and the input signal of
IC107-35 pin becomes a high level.
[Paper Sensor]
6.12.8. Paper Exit Sensor..... "PAPER JAMMED"
The sensor detects whether the recording paper exit out or not.
When there is no recording paper at the position of the sensor, the shelter plate closes the sensor light, the photo-transistor fot torus
OFF, and the input signal of IC107-4pin becomes high level.
When the recording paper reach the exit sensor, the shelter plate let the sensor light passing through, the photo-transistor ON, and
the input signal of IC107-4pin becomes a low level.
[Exit Sensor]
When there is no recording paper at the position of the sensor, the shelter plate closes the sensor light, the photo-transistor fot torus
OFF, and the input signal of IC107-4pin becomes high level.
When the recording paper reach the exit sensor, the shelter plate let the sensor light passing through, the photo-transistor ON, and
the input signal of IC107-4pin becomes a low level.
[Exit Sensor]
Photo-transistor
Signal (IC107-35 pin)
Recording Paper Set
ON
Low level
No Recording Paper
OFF
High level
Photo-transistor
Signal (IC107-4 pin)
No Paper
OFF
High level
Paper Exist
ON
Low level
Click on the first or last page to see other KX-FLC413UA service manuals if exist.