Panasonic KX-FC968RU Service Manual ▷ View online
9
KX-FC968RU-T
2.3.
Insulation Resistance Test
1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part
(screw heads, control shafts, bottom frame, etc.).
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.
4. If the measurement is outside the specified limits, there is a possibility of a shock hazard.
2.4.
Battery Caution
1. Danger of explosion if battery is incorrectly replaced.
2. Replace only with the same or equivalent type recommended by the manufacturer.
3. Dispose of used batteries according to the manufacturer's Instructions.
2. Replace only with the same or equivalent type recommended by the manufacturer.
3. Dispose of used batteries according to the manufacturer's Instructions.
10
KX-FC968RU-T
3 Specifications
Any details given in these instructions are subject to change without notice.
3.1.
Base Unit
*
1
Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the other
party’s machine.
*
2
Transmission speed is based upon the ITU-T No. 1 Test Chart with original mode. If the capability of the other party’s machine is
inferior to your unit, the transmission time may be longer. (Refer to ITU-T No.1 Test Chart (P.187).)
*
3
If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will
be retained in memory.
be retained in memory.
*
4
Recording time may be reduced by the calling party’s background noise.
Applicable Lines:
Public Switched Telephone Network
Document Size:
Max. 216 mm in width, Max. 600 mm in length
Effective Scanning Width:
208 mm
Recording Paper Size:
216 mm
× max. 30 m roll
Effective Printing Width:
208 mm
Transmission Time*
1
:
Approx. 12 s/page (ECM-MMR)*
2
Scanning Density:
Horizontal: 8 pels/mm
Vertical:
3.85 lines/mm - in standard resolution
7.7 lines/mm - in fine/photo resolution
15.4 lines/mm - in super fine resolution
Vertical:
3.85 lines/mm - in standard resolution
7.7 lines/mm - in fine/photo resolution
15.4 lines/mm - in super fine resolution
Photo Resolution:
64-level
Scanner Type:
Contact Image Sensor
Printer Type:
Thermal printing
Data Compression System:
Modified Huffman (MH), Modified READ (MR), Modified Modified READ (MMR)
Modem Speed:
9,600 / 7,200 / 4,800 / 2,400 bps; Automatic Fallback
Operating Environment:
5—35
°C, 20—80% RH (Relative Humidity)
Dimensions:
Approx. height 127 mm
× width 368 mm × depth 225 mm
Mass (Weight):
Approx. 2.8 kg
Power Consumption:
Standby: Approx. 4.5 W
Transmission: Approx. 16 W
Reception: Approx. 35 W (When receiving a 20% black document)
Copy: Approx. 40 W (When copying a 20% black document)
Maximum: Approx. 130 W (When copying a 100% black document)
Transmission: Approx. 16 W
Reception: Approx. 35 W (When receiving a 20% black document)
Copy: Approx. 40 W (When copying a 20% black document)
Maximum: Approx. 130 W (When copying a 100% black document)
Power Supply:
220 V - 240 V AC, 50/60 Hz
Fax Memory Capacity*
3
:
Approx. 25 pages of memory transmission
Approx. 28 pages of memory reception
(Based on the ITU-T No. 1 Test Chart in standard resolution, without using the
Error Correction Mode.)
Approx. 28 pages of memory reception
(Based on the ITU-T No. 1 Test Chart in standard resolution, without using the
Error Correction Mode.)
Voice Memory Capacity*
4
:
Approx. 15 minutes of recording time
LED light of CIS properties:
LED radiation output: Max. 1 mW
Wavelength: Yellowish Green 570 nm typ.
Emission duration: Continuous
Wavelength: Yellowish Green 570 nm typ.
Emission duration: Continuous
11
KX-FC968RU-T
3.2.
Cordless Handset
Standard:
DECT (Digital Enhanced Cordless Telecommunications)
GAP (Generic Access Profile)
GAP (Generic Access Profile)
Number of Channels:
120 Duplex channels
Frequency Range:
1.88 GHz to 1.9 GHz
Duplex Procedure:
TDMA (Time Division Multiple Access)
Channel Spacing:
1,728 kHz
Bit Rate:
1,152 kbit/s
Modulation:
GFSK (Gaussian Frequency Shift Keying)
RF Transmission Power:
Average: Approx. 10 mW
Maximum: Approx. 250 mW
Maximum: Approx. 250 mW
Voice Coding:
ADPCM 32 kbit/s
Operating Environment:
0
°C - 40°C, 20% - 80% RH (Relative Humidity)
Operation Range:
Up to 300 m outdoors, Up to 50 m indoors, depending on the condition
Dimensions:
Approx. height 158 mm
× width 48 mm × depth 30 mm
Mass (Weight):
Approx. 130 g
12
KX-FC968RU-T
4 General/Introduction
4.1.
Optional Accessories
*
1
Use only the included or specified recording paper. Using other recording paper may affect print quality and/or
cause excessive wear to the thermal head.
*
*
2
Replacement batteries may have a different capacity from that of the supplied batteries.
Model No./Part No.
Item
Specifications/Usage
KX-A106
Standard thermal recording paper
*1
216 mm
× 30 m roll, with 25 mm core
P03P or HHR-4MRE
Rechargeable batteries
*2
2 rechargeable nickel metal hydride (Ni-MH) batteries, AAA (R03) size
KX-TGA641RU
Additional digital cordless handset
-------------------
KX-A272
DECT repeater
-------------------
Click on the first or last page to see other KX-FC968RU service manuals if exist.