Panasonic DVD-S511E / DVD-S511EB / DVD-S511EG Service Manual ▷ View online
9.5. Service mode table 2
Press various button combinations on the player and remote control unit can activate the service modes. please carry out your
operation based on the remote control supplied with Panasonic DVD player of previous models.
operation based on the remote control supplied with Panasonic DVD player of previous models.
Item
Player mode and button
combination
Function
FL Display
Cancellation
method
Jitter check
In PLAY mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “5”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
PLAY and
OPEN/CLOSE buttons
on the player, and “5”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
Jitter check
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting. When target block data failed
to be read out, the counter advances
by one increment. When the failure is
caused by minor error, it may be
corrected when retried to enable
successful reading. In this case, the
counter advances by one. When the
error persists even after retry, the
counter may jump by two or more.
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting. When target block data failed
to be read out, the counter advances
by one increment. When the failure is
caused by minor error, it may be
corrected when retried to enable
successful reading. In this case, the
counter advances by one. When the
error persists even after retry, the
counter may jump by two or more.
Jitter rate is shown in decimal notation to one
place of decimal.
Focus drive value is shown in hexadecimal
notation.
“J 078 005 AF”
Jit rate = 7.8%
Read error counter = 5
Focus drive value = 0xAF
place of decimal.
Focus drive value is shown in hexadecimal
notation.
“J 078 005 AF”
Jit rate = 7.8%
Read error counter = 5
Focus drive value = 0xAF
Press STOP or
OPEN/CLOSE
button.
OPEN/CLOSE
button.
Error code check
In any mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “0”
button on the remote
control unit. *With
pointing of cursor up
and down on display,
the panel controller
switches serial number
of history and sends out
the command
accordingly.
PLAY and
OPEN/CLOSE buttons
on the player, and “0”
button on the remote
control unit. *With
pointing of cursor up
and down on display,
the panel controller
switches serial number
of history and sends out
the command
accordingly.
Error code check
The latest error code stored in
FLASHROM is displayed.
The latest error code stored in
FLASHROM is displayed.
Error code (play_err) is expressed in the
following convention.
following convention.
* “nn” denotes the serial number of history.
(01~20)
* “xx” denotes the error code.
(01~20)
* “xx” denotes the error code.
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
Initial setting of
laser drive current
laser drive current
In STOP (no disc)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and
PAUSE button on the
remote control unit.
(Press “FL SELECT”
key on the remote
control unit to change
the FL display for
Display1 or Display2.)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and
PAUSE button on the
remote control unit.
(Press “FL SELECT”
key on the remote
control unit to change
the FL display for
Display1 or Display2.)
Initial setting of laser drive current
Initial current value for each of DVD
laser and CD laser is seperately
saved in FLASHROM.
Initial current value for each of DVD
laser and CD laser is seperately
saved in FLASHROM.
The value denotes the current in decimal
notation. The above example shows the initial
current is 34mA and 32mA for DVD and CD
respectively when the laser is switched ON.
notation. The above example shows the initial
current is 34mA and 32mA for DVD and CD
respectively when the laser is switched ON.
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
DVD laser drive
current
measurement
current
measurement
In STOP (no disc)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and
FUNCTIONS button on
the remote control unit.
(Press “FL SELECT”
key on the remote
control unit to change
the FL display for
Display1 or Display2.)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and
FUNCTIONS button on
the remote control unit.
(Press “FL SELECT”
key on the remote
control unit to change
the FL display for
Display1 or Display2.)
DVD laser drive current measurement
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in
FLASHROM. Because the initial
current value is necessary when
displaying, an error may occur if no
value stored.
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in
FLASHROM. Because the initial
current value is necessary when
displaying, an error may occur if no
value stored.
The value denotes the current in decimal
notation. The above example shows the initial
current is 34mA and the measured value is
32mA when the DVD laser is switched ON.
notation. The above example shows the initial
current is 34mA and the measured value is
32mA when the DVD laser is switched ON.
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
CD laser drive
current
measurement
current
measurement
In STOP (no disc)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and
QUICK OSD button on
the remote control unit.
(Press “FL SELECT”
key on the remote
control unit to change
the FL display for
Display1 or Display2.)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and
QUICK OSD button on
the remote control unit.
(Press “FL SELECT”
key on the remote
control unit to change
the FL display for
Display1 or Display2.)
CD laser drive current measurement
CD laser drive current is measured
and the result is displayed together
with the initial value stored in
FLASHROM.
CD laser drive current is measured
and the result is displayed together
with the initial value stored in
FLASHROM.
The value denotes the current in decimal
notation. The above example shows the initial
current is 28mA and the measured value is 26
mA when the laser is switched ON.
notation. The above example shows the initial
current is 28mA and the measured value is 26
mA when the laser is switched ON.
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
25
DVD-S511E / DVD-S511EB / DVD-S511EG
Item
Player mode and button
combination
Function
FL Display
Cancellation
method
Version display
In STOP (no disc) or
PLAY mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “7”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
PLAY mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “7”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
Version display
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
Lighting of display
tube
tube
In any mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “9”
button on the remote
control unit.
PLAY and
OPEN/CLOSE buttons
on the player, and “9”
button on the remote
control unit.
Lighting of display tube
Lighting of all display tube
Repeat the same
operation.
operation.
Dealer´s lock
ON/OFF shift
function
ON/OFF shift
function
In PLAY mode, press
STOP button on the
player, and POWER
button on the remote
control unit.
STOP button on the
player, and POWER
button on the remote
control unit.
Dealer´s lock ON/OFF shift function
The lock is switched ON or OFF.
When dealer´s lock is on, it prohibits
switching off of the secondary power
and tray opening. When the lock is
switched, its ON/OFF status is stored
in FLASHROM.
The lock is switched ON or OFF.
When dealer´s lock is on, it prohibits
switching off of the secondary power
and tray opening. When the lock is
switched, its ON/OFF status is stored
in FLASHROM.
“LOC” sign appears when dealer´s lock is
switched on, or when POWER button or
OPEN/CLOSE button is pressed while the lock
is on.
“UNLOC” sign appears when dealer´s lock is
switched off.
switched on, or when POWER button or
OPEN/CLOSE button is pressed while the lock
is on.
“UNLOC” sign appears when dealer´s lock is
switched off.
Repeat the same
operation.
operation.
Initialization
In STOP (no disc)
mode, press STOP,
PLAY and POWER
buttons on the payer for
3 seconds or longer.
mode, press STOP,
PLAY and POWER
buttons on the payer for
3 seconds or longer.
Initialization
User settings are cancelled and
player is initialized to factory setting.
User settings are cancelled and
player is initialized to factory setting.
INI
All reset
When initialization by
the user is performed
and “INITIALIZATION”
is displayed, press
STOP, PLAY and
OPEN/CLOSE buttons
on the player.
the user is performed
and “INITIALIZATION”
is displayed, press
STOP, PLAY and
OPEN/CLOSE buttons
on the player.
Initialization
User settings are cancelled and
player is initialized to factory setting.
The setting resistance reference
value and unit information spreaded
globally of the OP_CON unit are
stored in FLASHROM.
Note: the operation timer of the laser
and spindle motor is not initialized.
User settings are cancelled and
player is initialized to factory setting.
The setting resistance reference
value and unit information spreaded
globally of the OP_CON unit are
stored in FLASHROM.
Note: the operation timer of the laser
and spindle motor is not initialized.
RESET
Region display
In STOP (no disc) or
PLAY mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “6”
button on the remote
control unit.
PLAY mode, press
PLAY and
OPEN/CLOSE buttons
on the player, and “6”
button on the remote
control unit.
Region display and unit setting
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
Timer 1 check
In STOP (no disc)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and “1”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and “1”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
Timer 1 check
Laser operation timer is measured
separately for DVD laser and CD
laser.
Laser operation timer is measured
separately for DVD laser and CD
laser.
T1_1234_5678 (display1/display2)
Shown to the left is DVD laser time and to the
right CD laser time.
Time is shown in 4 digits of decimal notation in
a unit of 10 hours.
“0000” will follow “9999”.
Shown to the left is DVD laser time and to the
right CD laser time.
Time is shown in 4 digits of decimal notation in
a unit of 10 hours.
“0000” will follow “9999”.
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
Timer 1 reset
While displaying Timer
1 data, press PLAY and
OPEN/CLOSE buttons
on the player, and “2”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
1 data, press PLAY and
OPEN/CLOSE buttons
on the player, and “2”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
Timer 1 reset
Laser operation timer is reset.
Laser operation timer is reset.
T1_0000_0000 (display1/display2)
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
26
DVD-S511E / DVD-S511EB / DVD-S511EG
Item
Player mode and button
combination
Function
FL Display
Cancellation
method
Timer 2 check
In STOP (no disc)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and “3”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
mode, press PLAY and
OPEN/CLOSE buttons
on the player, and “3”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
Timer 2 check
Spindle motor operation timer
Spindle motor operation timer
T2_12345 (display1/display2)
Time is shown in 5 digits of decimal notation in
a unit of 1 hours.
“00000” will follow “99999”.
Time is shown in 5 digits of decimal notation in
a unit of 1 hours.
“00000” will follow “99999”.
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
Timer 2 reset
While displaying Timer
2 data, press PLAY and
OPEN/CLOSE buttons
on the player, and “8”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
2 data, press PLAY and
OPEN/CLOSE buttons
on the player, and “8”
button on the remote
control unit. (Press “FL
SELECT” key on the
remote control unit to
change the FL display
for Display1 or
Display2.)
Timer 2 reset
Spindle motor operation timer is
reset.
Spindle motor operation timer is
reset.
T2_00000 (display1/display2)
Cancelled
automatically 5
seconds later.
automatically 5
seconds later.
27
DVD-S511E / DVD-S511EB / DVD-S511EG
9.6. Sales demonstration lock function
This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function.
“LOC” is displayed on the unit, and ordinary operation is disabled.
“LOC” is displayed on the unit, and ordinary operation is disabled.
9.6.1. Setting
The sales demonstration lock is set by simultaneously pressing PLAY and OPEN/CLOSE buttons on the player and QUICK
REPLAY button on the remote control unit for 1 second or longer.
REPLAY button on the remote control unit for 1 second or longer.
9.6.2. Cancellation
The lock can be cancelled by the same procedure as used in setting. (“UNLOC” is displayed on cancellation. Disconnecting the
power cable from power outlet does not cancel the lock.)
power cable from power outlet does not cancel the lock.)
9.7. Handling After Completing Repairs
Use the following procedure after completing repairs.
9.7.1. Method
Confirm that the power is turned on:
1. Press the “OPEN/CLOSE” button to close the tray.
2. Press the “POWER” button to turn off the power.
3. Disconnect the power plug from the outlet.
9.7.2. Precautions
Do not disconnect the power plug from the outlet with the tray still open, then close the tray manually.
28
DVD-S511E / DVD-S511EB / DVD-S511EG
Click on the first or last page to see other DVD-S511E / DVD-S511EB / DVD-S511EG service manuals if exist.