Panasonic DVD-LS837EEK Service Manual ▷ View online
13
8.1.
Disassembly
Caution to be taken when disassembling and reassembling the unit
• Disconnect the flexible cable from the main P.C.B. before disassembling the monitor assembly.
• Do not apply undue force on the flexible cable. There is a danger of breaking the cable.
• Do not touch the terminals of the flexible cable with your bare hands.
• Disassembly and reassembly should be performed in the specified order.
• Hold the LCD panel by its edges.
• Do not press the LCD panel strongly.
• Do not apply undue force on the flexible cable. There is a danger of breaking the cable.
• Do not touch the terminals of the flexible cable with your bare hands.
• Disassembly and reassembly should be performed in the specified order.
• Hold the LCD panel by its edges.
• Do not press the LCD panel strongly.
*If the LCD panel was pressed strongly by chance during disassembly or reassembly, leave it for about 10 seconds before
energizing the panel.
energizing the panel.
• To clean the LCD panel, wipe with a soft colth, such as gauze, saturated with isopropyl alcohol.
* Do not wipe the LCD panel with a dry gauze.
* Never use water for cleaning the LCD panel.
* Never use the following solvents:
(ketone: acetone and others)
(aromatic compounds: xylene, toluene)
(halogenides)
* If the water splashes on the LCD panel, wipe it away immediately.
* Never use water for cleaning the LCD panel.
* Never use the following solvents:
(ketone: acetone and others)
(aromatic compounds: xylene, toluene)
(halogenides)
* If the water splashes on the LCD panel, wipe it away immediately.
14
8.2.
P.C.B. location
8.3.
Main Cabinet Of The Unit
Removing battery pack
Release the lock lever and remove the battery pack in the
direction of the arrow.
direction of the arrow.
1. Remove the 14 screws from the bottom of the unit.
2. Release the latches and remove the bottom cabinet.
15
8.4.
Traverse Assembly
8.4.1.
Removing Traverse Assembly
1. Solder the 1 laser short land on the flexible cable.
2. Unlock the connectors and remove the flexible cables.
2. Unlock the connectors and remove the flexible cables.
8.4.2.
Reinstalling Traverse Assembly
1. Reinstall the traverse assembly to the specified pin of the
unit.
2. Reinstall the flexible cable of the optical pickpup unit and
lock it securely.
3. Remove the solder of each laser short land of the flexible
cable.
Caution:
Caution:
Remove the solders completely: otherwise the laser
diode won’t emit light.
diode won’t emit light.
4. Reinstall the spindle flexible cable as shown figure.
16
8.5.
Optical Pick-up Unit
8.5.1.
Removing Optical Pick-up Unit
Make sure that the traverse assembly removed before trying to
remove the optical pick-up unit.
When removing the traverse assembly, solder the one laser
short land on the flexible cable of the optical pick-up unit.
remove the optical pick-up unit.
When removing the traverse assembly, solder the one laser
short land on the flexible cable of the optical pick-up unit.
1. Remove the two screws securing the main shaft retainer.
2. Remove the main shaft retainer.
3. Slide the main shaft in the direction indicated by the arrow
2. Remove the main shaft retainer.
3. Slide the main shaft in the direction indicated by the arrow
to remove the optical pick-up unit.
8.5.2.
Reinstalling Optical Pick-up Unit
The optical pick-up unit is factory adjusted. Do not touch the
adjustment screw.
adjustment screw.
1. Reassemble the disassembled parts in the reverse order
of disassembly.
2. When reinstalling the traverse assembly on the main unit
after installing the optical pick-up unit, make sure to
remove the solder from each of the two laser short lands
on the flexible cable.
remove the solder from each of the two laser short lands
on the flexible cable.
Caution:
• Remove the solders completely; otherwise the laser diode
won't emit light.
• After replacing the optical pick-up unit, check the quality of
images played back and make optical adjustment.
8.6.
Disc Motor
8.6.1.
Removing Disc Motor
1. Remove the adjustment screws A, B, and C.
2. Remove the disc motor.
2. Remove the disc motor.
8.6.2.
Caution To Be Taken When Replac-
ing The Disc Motor
ing The Disc Motor
1. The mounting screws of the disc motor also serve as
adjustment screws. When reinstalling the disc motor, first
turn the screws A, B, and C as far as they go by usual
force to secure them (do not overtighten).
turn the screws A, B, and C as far as they go by usual
force to secure them (do not overtighten).
2. Back off the adjustment screws A and C two complete
turns and secure them.
3. Back off the adjustment screw B one and a half turns and
secure them.
• This makes it nearly possible to play back disks and
adjust the jitter.
Thereafter, adjust the adjustment screws C and A as
indicated.
Thereafter, adjust the adjustment screws C and A as
indicated.
Click on the first or last page to see other DVD-LS837EEK service manuals if exist.