DOWNLOAD Panasonic DVD-LS70EB / DVD-LS70EE / DVD-LS70EG / DVD-LS92EB / DVD-LS92EE / DVD-LS92EG Service Manual ↓ Size: 4.43 MB | Pages: 68 in PDF or view online for FREE

9

+5 to +35

°C 

5 to 85% RH (no condensation) 

DVD 

[DVD-Video, DivX

*4, *6

]

DVD-R

[DVD-Video,  DivX

*4, *6

, 

JPEG

*3,4,5

, MP3

*2,4

]

DVD-R DL

[DVD-Video]

DVD-RW

[DVD-Video, DivX

*4, *6

, 

JPEG

*3,4,5

, MP3

*2,4

]

+R/RW [Video]
+R DL 

[Video]

CD, CD-R/RW

[CD(CD-DA), Video CD, SVCD

*1

, 

MP3

*2,4

, JPEG 

*3,4,5

, DivX

*4, *6

]

*1: Conforming to IEC62107
*2: MPEG-1 Layer3, MPEG-2 Layer3
*3: Exif Ver 2.1 JPEG Baseline files
 Picture resolution:
16:9 picture: 4

×4

~

5760

×3240 pixels

 4:3 picture:  4

×4

~

5760

×4320 pixels 

 (sub sampling is  4:2:2 or 4:2:0)
*4: The total combined maximum number of recognizable audio, 
picture and movie contents and groups: 2000 audio, picture and 
movie contents and 200 groups.
*5: Extremely long and slender pictures may not be displayed.
*6: Plays all versions of Divx video (including Divx6) with standard 
playback of Divx  media files. Certified th the Divx Home Theater 
Profiles.

PLA/NTSC selectalbe

9 inch, TFT wide-screen LCD 
(640

×234×RGB)(LS92EB/EG/EE)

7 inch, TFT wide-screen LCD 
(480

×234×RGB)(LS70EB/EG/EE)

Output terminal:

Mini-jack 3.5mm 

 

Number of terminals:

1 system

Output level:

1 Vp-p (75

Ω)

Horizontal resolution:

More than 500 lines

Y   S/N:

More than 60dB

Output level:

1.5Vrms (1kHz, 0dB, 10k

Ω)

(1) Frequency response:

 DVD (linear audio):

4Hz-22kHz (48kHz sampling)
4Hz-44kHz (96kHz sampling)

 CD Audio:

4Hz-20kHz

(2) S/N ratio:

100dB

(3) Dynamic range:

80dB

(4) Total harmonic distortion:

0.1%

Output:

1.2W+1.2W (10% Distortion)

Output:

stereo mini jack  3.5mm  

Number of terminals:

2 systems

Number of terminals:

1 systems

USB Standard:

USB2.0 Full Speed

When brightness is set to “-
5” while playing DVD:

11 hours (DY-DB20) / 14 hours
 (DY-DB30) (LS92EB/EG/EE)
5 hours (CGR-H711) / 11 hours
 (CGR-H712) (LS70EB/EG/EE)

When brightness is set to “0” 
while playing DVD:

 9.5 hours (DY-DB20) / 12 hours 
(DY-DB30) (LS92EB/EG/EE)
 5 hours (CGR-H711) / 9.5 hours 
(CGR-H712) (LS70EB/EG/EE)

When brightness is set to 
“+5” while playing DVD:

8 hours (DY-DB20) / 10 hours 
(DY-DB30) (LS92EB/EG/EE)
4 hours (CGR-H711) / 8 hours 
(CGR-H712) (LS70EB/EG/EE)

When LCD panel is off while 
playing DVD:

11 hours (DY-DB20) / 14 hours
 (DY-DB30) (LS92EB/EG/EE)
5.5 hours (CGR-H711) / 11 hours
 (CGR-H712) (LS70EB/EG/EE)

°C)

7 hours (DY-DB20) / 8 hours
 (DY-DB30)
5 hours (CGR-H711) / 7 hours
 (CGR-H712)

Wave length:

655 nm/790 nm (DVD/CD)

Laser power:

CLASS 1M/ CLASS 1 (DVD/CD) 

DC 12V (DC IN terminal) /
DC 7.2V (Exclusive battery
 terminal)

14W (Unit only: 12W) /
Standby mode approx. 
0.5W/Recharge mode 12W 

 100-240V, 50/60Hz

22W

12V, 1.3A

12V, 1.5A (Vehicle with 12V
 battery only)

Voltage:

7.2V

Capacity :

4200mAh (LS92EB/EG/EE)
2100mAh (LS70EB/EG/EE)

×H×D):

242.6mm(W) x 173.5mm(D) x 
46.0mm(H) 
[9-9/16” x 6-27/32” x1-13/16”]
24.6mm at lowest point [31/32”]
[D=179.3mm H=51.5mm  
including battery]
[D=7-1/16”   H=2-1/32”]
(LS92EB/EG/EE)
[D=173.5mm H=46.6mm
including battery]
[D=6-27/32”   H=1-27/32”] 
(LS70EB/EG/EE)

approximately 1117g (39.4oz) 
(LS92EB/EG/EE)
approximately 922g (32.52oz) 
(LS70EB/EG/EE)

approximately 885g  (31.22oz) 
(LS92EB/EG/EE)
approximately 780g  (27.51oz) 
(LS70EB/EG/EE)

10

This model uses lead free
solder(PbF).

Specifications are subject to 
change without notice.

11

This model is using a lithium battery for the remote control ass’y.
NOTE:

The lithium battery is a critical component. ( Type No.: CR2025 Manufactured by Panasonic. )
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.

12

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.  

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86 F) more than that
of the normal solder.

- The lead free solder has to be used when repairing the equipment for which the lead free solder is used.(Definition: The letter
of "PbF" is printed on the PCB using the lead free solder.)
- To put lead free solder, it should be well molten and mixed with the original lead free solder.
- Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
- Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
- Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350+-30
degrees C (662+-86 F).

- The following 3 types of lead free solder are available through the service parts route.
   RFKZ03D01KS-----------(0.3mm 100g Reel)
   RFKZ06D01KS-----------(0.6mm 100g Reel)
   RFKZ10D01KS-----------(1.0mm 100g Reel)

* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

The letter of “PbF” is printed either foil side or components side on the PCB
using the lead free solder. (See right figure)