Panasonic DMR-ES10EE / DMR-ES10GC / DMR-ES10GCS / DMR-ES10GN Service Manual ▷ View online
10 Assembling and Disassembling
10.1. Disassembly Flow Chart
The following chart is the procedure for disassemblin g the casing and inside parts for internal inspection when carrying out the
servicing.
servicing.
To assemble the unit, reverse the steps shown in the chart below.
10.2. P.C.B. Positions
21
DMR-ES10EE / DMR-ES10GC / DMR-ES10GCS / DMR-ES10GN
10.3. Top Case
1. Remove the 2 screws (A) and 3 screws (B).
2. Slide Top Case rearward and open the both ends at rear
2. Slide Top Case rearward and open the both ends at rear
side of the Top Case a little and lift the Top Case in the
direction of the arrows.
direction of the arrows.
10.4. Front Panel
1. Unlock 2 tabs (A) and 3 tabs (B) in this order to remove
Front Panel.
(The tab (A) and (B) should be unlocked at the same time,
respectively.)
respectively.)
10.5. Digital P.C.B.
1. Remove FFC and a Screw (A).
2. Lift up Digital P.C.B. slightly so to disconnect Connector to
2. Lift up Digital P.C.B. slightly so to disconnect Connector to
remove Digital P.C.B.
CAUTION 1:
When replacing Digital P.C.B., pay attention as below.
22
DMR-ES10EE / DMR-ES10GC / DMR-ES10GCS / DMR-ES10GN
10.6. DVD-RAM Drive
1. Remove 3 Screws (A) to remove DVD-RAM Drive.
2. Lift up DVD-RAM Drive slightly and remove FFC and
2. Lift up DVD-RAM Drive slightly and remove FFC and
remove Cable between DVD-RAM Drive and Main P.C.B.
10.7. Power P.C.B.
1. Remove Screw (A).
2. Remove 3 Screws (B) and disconnect Connector (A).
3. Unlock Power P.C.B. from a Flange to remove Power
3. Unlock Power P.C.B. from a Flange to remove Power
P.C.B.
10.8. Rear Panel
1. Remove 7 Screws (A), and Screw (B).
2. Unlock 2 Locking Tabs (A) to remove Rear Panel.
23
DMR-ES10EE / DMR-ES10GC / DMR-ES10GCS / DMR-ES10GN
10.9. Front (L) P.C.B.
1. Remove a Screw (A) to remove Front (L) P.C.B.
10.10. Main P.C.B.
1. Disconnect Connector (A) for Front (L) P.C.B.
2. Remove 9 Screws (A).
3. Remove Power P.C.B. Angle, Digital P.C.B. Angle and
2. Remove 9 Screws (A).
3. Remove Power P.C.B. Angle, Digital P.C.B. Angle and
disconnect Connector (A) to remove Main P.C.B.
10.11. Tuner P.C.B. and Nicam
Decoder P.C.B.
1. Pull out the Tuner P.C.B. in the direction of the arrow.
2. Remove the solders and pull out the Nicam Decoder P.C.B.
2. Remove the solders and pull out the Nicam Decoder P.C.B.
24
DMR-ES10EE / DMR-ES10GC / DMR-ES10GCS / DMR-ES10GN
Click on the first or last page to see other DMR-ES10EE / DMR-ES10GC / DMR-ES10GCS / DMR-ES10GN service manuals if exist.