DOWNLOAD Panasonic DMP-B200P / DMP-B200PC Service Manual ↓ Size: 4.26 MB | Pages: 55 in PDF or view online for FREE

5

This model is using a lithium battery for remote control ass’y.
NOTE:

This Lithium battery is a critical component.
(Type No.: CR2025 Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.

6

This service manual contains technical information, which allow service personnel's to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation. 

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86

°F) more than that

of the normal solder.

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees

C (662±86

°F).

• The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)

* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

1. The service manual does not contain the following information, because of the impossibility of servicing at component level

without concerned equipment/facilites.

a. Schematic diagram, Block Diagram and PCB layout of MAIN PCB.
b. Parts list for individual parts for MAIN PCB.

2. The following category is/are recycle module part. please send it/them to Central Repair Center.

• TRV/MAIN PCB MODULE (B200PC:RFKNB200PC)

3. For USA market(B200P):

The Traverse and main P.C.B for PBD model is offered respectively for the market maintenaince.
For the information about pairing adjustment of the Traverse and main P.C.B.,please refer to "10.3 Adjustment Instruction
when Exchange the OPU Ass'y or Main P.C.B. adjustment value initialization adjust" .

• The laser diode in the traverse unit (optical pick-up) may break down due to potential difference caused by static electricity of

clothes or human body.
So, be careful of electrostatic breakdown during repair of the traverse unit (optical pick-up).

• As for parts that use optical pick-up (laser diode), the optical pick-up is destroyed by the static electricity of the working environ-

ment.
Repair in the working environment that is grounded.

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
 
(See right figure)

7

• Put a conductive material (sheet) or steel sheet on the area where the traverse unit (optical pick-up) is placed, and ground the

sheet.

• Use the anti-static wrist strap to discharge the static electricity from your body.

1. Do not subject the traverse unit (optical pick-up) to hard shock as it is high precision mechanism.
2. Install the traverse unit, and then remove the short pin to discharge.

Connect the connector in a short time.

3. Take care not to apply excessive stress to the flexible cable.
4. Do not turn the variable resistor (laser power adjustment).

It has already been adjusted.

8

DC12V(DC IN terminal)
DC7.2V
(Exclusive battery terminal)

Play Mode:

Approx. 15W (Unit only 
approx.12W) 

Recharge Mode:
(Quick Start [OFF]):

Approx. 18W

Recharge Mode:
(Quick Start [ON]):

Approx. 22W

Standby Mode:
(Quick Start [OFF]):

Approx. 0.3W (B200P)
Approx. 0.4W (B200PC)

Standby Mode:
(Quick Start [ON]):

Approx. 4W (B200P)
Approx. 4.5W (B200PC)

(using included AC adaptor)

Power source:

110V-240V, 50/60Hz

Power consumption:

36W

DC output:

12V, 2000mA

DC output:

12V, 2A
Vehicle with 12V battery only

Voltage:

7.2V

Capacity:

4500mAh(typ)
4200mAh(min)
31Wh

238mm x 188.3mm x 52.7mm
(9

3

/8" x 7

13

/32" x 2

1

/16")

Including battery:

approximately 1376g [48.52oz]

Without battery:

approximately 1143g [40.30oz]

+5

°C to +35°C(+41 to +95°F)

10% - 80%RH (no condensation)

8.9" -Si, TFT wide-screen LCD 
(1024 x 600 x RGB)

number of terminals:

1 system

output:

0.5W + 0.5W (8

Ω)

output:

stereo mini-jack(

3.5mm)

number of terminals:

1 system

°C, ECO-charge OFF)

when brightness is set to
"-5" while playing DISC:

4 hours/5 hours (DY-DB30)/ 
8 hours (DY-DB300)

when brightness is set to
"0" while playing DISC:

3.5 hours/4.5 hours (DY-DB30)/
7 hours (DY-DB300)

when brightness is set to
"+5" while playing DISC:

3 hours/3.75 hours (DY-DB30)/
6 hours (DY-DB300)

°C)

ECO-charge OFF:

4 hours/5 hours (DY-DB30)/
7 hours (DY-DB300)

ECO-charge ON:

3.25 hours/4 hours (DY-DB30)/
5.5 hours (DY-DB300)

Wave Length:

405nm/660nm/780nm (BD/DVD/
CD)

Laser power:

CLASS II/CLASS II/
CLASS I (BD/DVD/CD)
(B200P)
CLASS 1M/CLASS 1M/
CLASS 1M (BD/DVD/CD)
(B200PC)

DVD: #1
BD: Region A

Playable disc:

BD-Video:

BD-ROM Version2

BD-RE:

Version3 (SL:Single Layer/
DL:Dual Layer), JPEG

BD-R:

Version2 (SL:Single Layer/
DL:Dual Layer),
 MKV (*5), (*6), (*7) 

DVD-RAM:

DVD Video Recording format (*3), 
AVCHD format, JPEG

DVD-R:

DVD-Video format (*1), DVD 
Video Recording format(*1),  (*3) 
AVCHD format(*1), JPEG(*2), 
MP3(*2), MKV (*2), (*4), (*6), (*7)

DVD-R DL:

DVD-Video format (*1), DVD 
Video Recording format(*1),  (*3) 
AVCHD format(*1), JPEG(*2), 
MP3(*2), MKV (*2), (*4), (*6), (*7)

DVD-RW:

DVD-Video format (*1), DVD 
Video Recording format(*1),  (*3) 
AVCHD format(*1)

+R:

Video(*1), AVCHD format(*1)

+R DL:

Video(*1), AVCHD format(*1)

+RW:

Video(*1), AVCHD format(*1)

DVD-VIDEO:

DVD-Video format

CD-Audio:

CD-DA

CD-R/CD-RW:

CD-DA, JPEG(*2), MP3(*2), 
MKV (*2), (*6), (*7)

*1: Finalizing is necessary.
*2: ISO9660 level1 or 2(except for extended formats), Joliet.

This unit is compatible with multi-session.
This unit is not compatible with packet writing.

*3: CPRM discs are not supported.
*4: UDF1.02 without ISO9660, UDF1.5 with ISO9660.
*5: UDF2.5.
*6: Maximum number of folders recognizable:300 folders.

(including the root folder)
Maximum number of files recognizable:200 files.

*7: MPEG-4 AVC (H.264) profile is up to High Profile, Level 4.

 AAC-LC, MP3, Dolby Digital audio can be decoded.

SD Memory Card(*8) 
formatted FAT12, FAT16, 
FAT32(*9),exFAT(*10):

JPEG, AVCHD format, MPEG-2

*8: includes SDHC, SDXC card..

includes miniSD

 

Card(need a miniSD Adaptor.)

includes microSD/microSDHC/micro SDXC Card.    
(need a microSD Adaptor.)

*9: Not support long file name.
*10: SDXC only.

JPEG :
SD card, CD-R/RW, DVD-RAM, BD-RE, DVD-R:

Pixcels:

34x34~8192x8192