Panasonic Q-MECHANISM Service Manual ▷ View online
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0301000000.html
3.1 PREPARATION FOR DISASSEMBLY
TOP
PREVIOUS
NEXT
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0301000000.html (1 of 2) [02.10.2002 13:24:15]
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0301000000.html
TOP
PREVIOUS
NEXT
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0301000000.html (2 of 2) [02.10.2002 13:24:15]
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0302000000.html
3.2 DISASSEMBLY PROCEDURE
TOP
PREVIOUS
NEXT
No.
Item
Fig.
Procedure
1
Cassette Up Unit.
Fig. D1-1
1) Remove 3 screws. (Q1 &2 have 4 screws)
Fig. D1-2
2) Take coupling portion off from both S &T sides.
*2
H Amp Unit./(Only Q1 & Q2)
Fig. D2-1
1) Remove a screw from Shield case.
Fig. D2-2
2) Take Cylinder Flex. From connector.
Fig. D2-3
3) Remove a screw from H Amp Angle.
3
Cylinder Unit & RT Flex. Flame.
Fig. D3-1
1) Remove a screw from RT Flex. Flame.
Fig. D3-2
2) Remove 3 screws and then take Cylinder Spring out.
Fig. D3-3
3) Remove a screw and take RT Flex. Flame out.
4
LED Holder, Cover plate & Idler U.
Fig. D4-1
1) Pull up and remove LED Holder.
Fig. D4-2
2) Move LED Flat Cable out of position and unhook 2 springs.
Fig. D4-3
3) Remove 5 screws and remove Cover Plate & Idler U.
5
Sub Chassis Unit
Fig. D5-1
1) Remove 4 screws.
Fig. D5-2
2) Remove a screw and unhook a spring from Pinch Arm.
6
Pinch Arm & Center Gear
Fig. D6-1
1) Remove Cut Washer and take Pinch Arm out.
2) Take Center Gear out.
2) Take Center Gear out.
Fig. D6-2
3) Take Center Gear Spacer out.
7
Rail Unit
Fig. D7-1
1) Make half loading until / Connection Arm comes out.
Fig. D7-2
2) Disconnect Connection Arms.
a) Hold Loading Gear side.
b) Disconnect connection arms.
a) Hold Loading Gear side.
b) Disconnect connection arms.
Fig. D7-3
3) Remove 4 screws.
8
T-Loading Gear & S-Loading Gear
Fig. D8
1) Take T-Loading Gear out.
2) Remove Cut Washer on S-Loading Gear and take S-Loading Gear
out.
* Removed Cut Washer can not be used again.
2) Remove Cut Washer on S-Loading Gear and take S-Loading Gear
out.
* Removed Cut Washer can not be used again.
9
Gear Cover
Fig. D9
1) Remove a screw and slide Gear Cover to take out.
10
Pinch Beetle & Release Beetle
Fig. D10
1) Remove a washer and take Pinch Beetle and Release Beetle out
together.
together.
11
Tension Lever & Eject Arm.
Fig. D11
1) Remove a screw and take Tension Lever out.
2) Remove a washer and take Eject Arm out.
2) Remove a washer and take Eject Arm out.
12
Interface Gears
Fig. D12
1) Remove 4 Gears.
13
Cam Gear
Fig. D13
1) Remove Cam Gear.
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0302000000.html (1 of 23) [02.10.2002 13:24:22]
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0302000000.html
14
Chassis Radon
Fig. D14
1) Remove a washer.
15
Boat Radon
Fig. D15
1) Remove Boat radon.
16
Drive Gear
Fig. D16
1) Remove Drive Gear and a White Waher underneath.
17
Capstan Holder & Capstan Motor
Fig. D17-1
1) Remove 2 screws and take Capstan Holder out.
* It is not necessary to remove 2 screws for New Capstan Holder.
Because it shapes screw.
Because it shapes screw.
Fig. D17-2
2) Remove 3 screws and take Capstan Motor out downword.
18
Loading Motor unit & Mechanism Interface Flex.
Fig. D18-1
1) Remove 2 screws and take Loading Motor Unit out.
Fig. D18-2
2) Remove 4 screws and dissolder at Mode Sw.
*19 Mode Switch , Deceleration Gears & Tension Plate.
Fig. D19
1) Take Mode Sw out.
2) Remove a washer and take Deceleration Gear (A) out.
3) Take Deceleration Gear (B) out.
4) Remove 2 washers and take Tension Plate.
2) Remove a washer and take Deceleration Gear (A) out.
3) Take Deceleration Gear (B) out.
4) Remove 2 washers and take Tension Plate.
*20 T4 Guide , Eject Lever , Pulley Cover & Pulley.
Fig. D20-1
1) Remove a screw and take T4 Guide out.
Fig. D20-2
2) Remove a washer and take Eject Lever out.
Fig. D20-3
3) Remove 2 screw and take Pulley Cover out.
4) Take Pulley out.
*21 S3 Base U.
Fig. D21
1) Remove a screw for S3 adjustment and take S3 Base U.
* 1) Procedure 2 for H.Amp Unit is applied only Q1 & Q2 / mechanism. 2) Procedure 19 - 21 can be
changed in order.
changed in order.
Fig. D1-1
file:///C|/Documents%20and%20Settings/Someone/My%20Documents/202/s0302000000.html (2 of 23) [02.10.2002 13:24:22]
Click on the first or last page to see other Q-MECHANISM service manuals if exist.