Panasonic DMC-LC43PP / DMC-LC43PM / DMC-LC43E / DMC-LC43B / DMC-LC43A / DMC-LC43EN / DMC-LC43KR (serv.man2) Service Manual ▷ View online
9
DMC-LC43PP / DMC-LC43PM / DMC-LC43E / DMC-LC43B / DMC-LC43A / DMC-LC43EN / DMC-LC43KR
5 SERVICE NOTES
5.1. WHEN REPLACING THE MAIN C.B.A.
After replacing the MAIN C.B.A., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “CS-Web from AVC” web-site in “TSN system”, together with
Maintenance software.
Maintenance software.
5.2. SERVICE POSITION
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No.
Parts No.
Connection
Form
1
VFK1582A1225
FP9007 (MAIN) - FLASH UNIT
12PIN 0.5 FFC
2
VFK1582A1225
FP9006 (MAIN) - REAR OPERATION UNIT
12PIN 0.5 FFC
3
VFK1284
FP9003 (MAIN) - LCD UNIT
24PIN 0.5 FFC
4
VFK1576DC202
FP9004 (MAIN) - LCD BACK LIGHT UNIT
2PIN 1.0 Wire
5
VFK1582A1025
FP9005 (MAIN) - TOP OPERATION UNIT
10PIN 0.5 FFC
6
VFK1492
FP9002 (MAIN) - LENS UNIT
26PIN 0.5 FFC
7
VFK0977
FP9001 (MAIN) - CCD FLEX UNIT
21PIN 0.5 FFC
CAUTION
1. Be sure to discharge the capacitor for flash, which is connected with FLASH C.B.A.
(Refer to “HOW TO DISCHARGE THE CHARGING CAPACITOR ON MAIN C.B.A.”.)
10
DMC-LC43PP / DMC-LC43PM / DMC-LC43E / DMC-LC43B / DMC-LC43A / DMC-LC43EN / DMC-LC43KR
5.3. HOW TO DISCHARGE THE CAPACITOR ON MAIN C.B.A.
CAUTION:
1. Be sure to discharge the capacitor on FLASH C.B.A. after removing the Front case.
2. Be careful of the high voltage circuit on FLASH C.B.A. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and Remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
Ω
/5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on FLASH C.B.A. for approx. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
5.4. CLEANING LENS, OPTICAL VIEWFINDER AND LCD PANEL
Do not touch the surface of lens, optical viewfinder and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the optical viewfinder and LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the
their surface.
their surface.
Note:
A lens cleaning paper and lens cleaner are available at local camera shops and market place.
11
DMC-LC43PP / DMC-LC43PM / DMC-LC43E / DMC-LC43B / DMC-LC43A / DMC-LC43EN / DMC-LC43KR
5.5. HANDLING FOR THE MAIN C.B.A.
(Mounting parts)
Do not touch the lead part on the package of IC6005(VENUS) in servicing.
In case of touching, wipe with ethanol clean.
NOTE:
The coated version of IC6005 shall be after several lot of Mass-production.
If coated version of IC6005 is used, no need for covering with the “ASIC SHEET”.
12
DMC-LC43PP / DMC-LC43PM / DMC-LC43E / DMC-LC43B / DMC-LC43A / DMC-LC43EN / DMC-LC43KR
Click on the first or last page to see other DMC-LC43PP / DMC-LC43PM / DMC-LC43E / DMC-LC43B / DMC-LC43A / DMC-LC43EN / DMC-LC43KR (serv.man2) service manuals if exist.