Panasonic DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT Service Manual ▷ View online
53
11.3. General description (Lens cleaning: Interchangeable Lens/H-FS014042)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
Also do not exchange the 1st lens unit taking from others.
54
11.3.1.
Disassembly procedure
Important:
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
11.3.1.1. Removal of the Decoration Ring
1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
and lens glass), and peel off the decoration ring gently.
11.3.1.2. Removal of the 1st Lens Frame
Unit
1. Remove the 3 screws (A).
11.3.1.3. Removal of a dust /dirt
1. Blow off the dust on the surface of the lens with a blower
brush.
2. Use lens cleaning KIT(BK) (VFK1900BK), if necessary.
55
11.3.2.
Assembly procedure
Important:
When tightening the screw, use a torque driver (RFKZ0456)
by ordering the screwing order with specified torque
described in each step.
by ordering the screwing order with specified torque
described in each step.
11.3.2.1. Installation of the 1st lens frame
unit
1. Tighten the 3 screws (A) with specified torque in numeri-
cal order.
(Torque Driver: RFKZ0456)
(Torque: 10 ± 1.0 N-cm)
(Torque Driver: RFKZ0456)
(Torque: 10 ± 1.0 N-cm)
11.3.2.2. Installation of the Decoration Ring
1. Use the Name Ring fixture (RFKZ0507)
2. Use new Decoration ring. (Do not use the one which is
2. Use new Decoration ring. (Do not use the one which is
removed.)
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Block Diagram .......................................................................... S-2
S2.1. Overall Block Diagram .......................................................... S-2
S3. Schematic Diagram .................................................................. S-3
S3.1. Interconnection Diagram ....................................................... S-3
S3.2. Top Operation Schematic Diagram ....................................... S-4
S3.3. External LVF Schematic Diagram ......................................... S-5
S3.4. Flash Schematic Diagram ..................................................... S-6
S3.5. AF LED Schematic Diagram ................................................. S-6
S4. Print Circuit Board .................................................................... S-7
S4.1. Top P.C.B. ............................................................................. S-7
S4.1.1. Top P.C.B. (Component Side) ............................................ S-7
S4.1.2. Top P.C.B. (Foil Side) ......................................................... S-8
S4.2. External LVF P.C.B. ............................................................... S-9
S4.3. Flash P.C.B. .......................................................................... S-9
S4.4. AF LED P.C.B. ..................................................................... S-10
S5. Replacement Parts List .......................................................... S-11
S6. Exploded View ....................................................................... S-21
S6.1. Frame and Casing Section.................................................. S-21
S6.2. Camera Lens Section (1) .................................................... S-22
S6.3. Camera Lens Section (2) .................................................... S-23
S6.4. Packing Parts and Accessories Section (1) ........................ S-24
S6.5. Packing Parts and Accessories Section (2) ........................ S-25
S6.6. Packing Parts and Accessories Section (3) ........................ S-26
S6.7. Packing Parts and Accessories Section (4) ........................ S-27
Table of contents
Service Manual
DSC1101003CE
Diagrams and Replacement
Parts List
Model No.
DMC-GF2KPP
DMC-GF2KEB
DMC-GF2KEC
DMC-GF2KEE
DMC-GF2KEG
DMC-GF2KGC
DMC-GF2KGD
DMC-GF2KGH
DMC-GF2KGK
DMC-GF2KGN
DMC-GF2KGT
DMC-GF2PP
DMC-GF2GC
DMC-GF2GH
DMC-GF2CPP
DMC-GF2CEB
DMC-GF2CEC
DMC-GF2CEE
DMC-GF2CEG
DMC-GF2CGC
DMC-GF2CGD
DMC-GF2CGH
DMC-GF2CGK
DMC-GF2CGN
Digital Camera/Lens Kit/Double Lens Kit/Body
DMC-GF2CGT
DMC-GF2WEB
DMC-GF2WEG
DMC-GF2WGC
DMC-GF2WGD
DMC-GF2WGH
DMC-GF2WGK
DMC-GF2WGN
DMC-GF2WGT
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
Vol. 1
[DMC-GF2C]
Colour
(K)........Black Type
(S)........Silver Type (except EE/GK/GN/GT)
(R)........Red Type (except GC/GD/GN/GT)
(P)........Pink Type (only GC/GH/GK/GT)
(W).......White Type (except EB/EE)
(K)........Black Type
(S)........Silver Type (only PP/EB/EC/EG/GC)
(R)........Red Type (except GC/GD/GH/GN/GT)
(P)........Pink Type (only GC/GK)
(W).......White Type (except EB/EE/GH)
[DMC-GF2K]
[DMC-GF2W]
(K)........Black Type
(S)........Silver Type (only EB/EG/GC)
(R)........Red Type (only EB/EG/GH)
(P)........Pink Type (only GC)
(W).......White Type (except EB)
(K)........Black Type
DMC-GF2C series: Interchangeable Lens (H-H014) is bundled.
DMC-GF2K series: Interchangeable Lens (H-FS014042) is bundled.
DMC-GF2W series: Interchangeable Lens (H-H014/H-FS014042) is bundled.
[DMC-GF2]
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
Click on the first or last page to see other DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT service manuals if exist.