Panasonic DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT Service Manual ▷ View online
45
NOTE:
1. .When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, men-
tioned on the above table.
2. The Ref.B309 is no need to remove/install for disassembly and assembly.
If necessary, use VFK1390 (small driver) when screwing it..
(Fig. C1)
46
9.3.
Disassembly and Assemble Procedure for the Lens (H-FS014042)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. K1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the “11 Maintenance” for detailes.
As for procedure, refer to the “11 Maintenance” for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. K1.
NOTE:
NOTE:
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, men-
tioned on the above table.
2. The Ref.B413 is no need to remove/install for disassembly and assembly.
If necessary, use VFK1390 (small driver) when screwing it.
Interchangeable Lens (H-FS014042)
47
(Fig. K1)
48
10 Measurements and Adjustments
10.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
After updates it to the latest firmware, the adjustment is executed.
After updates it to the latest firmware, the adjustment is executed.
*1
• Inspect it, not only corresponding part is replaced, but also camera body is shocked and/or dropped.
• The Panasonic camera body in accordance with the Micro Four Thirds system (DMC-G1 unit, etc. marketed commodity: oper-
• The Panasonic camera body in accordance with the Micro Four Thirds system (DMC-G1 unit, etc. marketed commodity: oper-
ates normal) and a standard zoom lens H-FS014045 (marketed commodity: operates normal) is required as a reference
machine.
machine.
• Refer to the adjustment instruction in the adjustment software for details.
*2 NOTE: (When exchange the MAIN P.C.B.)
• Correspond by either the following when exchange the MAIN P.C.B. unavoidably by destruction and damage etc. of MAIN
P.C.B..
1. When it can turn on power, and the adjustment software can communicate with the camera body:
• Before replacing, proceed the VENUS FHD (IC6001) data backup from the unit. After replacing, overwrite the VENUS FHD
(IC6001) data with backup data from the unit, before proceeding the main body adjustment.
2. When it cannot turn on power, or the adjustment software cannot communicate with the camera body:
• The readjustment of mount box unit etc. are necessary.
• Refer to the adjustment instruction in the adjustment software for details.
• Refer to the adjustment instruction in the adjustment software for details.
Click on the first or last page to see other DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT service manuals if exist.