Panasonic DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT Service Manual ▷ View online
49
*3 NOTE: (After exchange the mount box unit)
• Execute the resolution inspection by the comparison with the standard model (DMC-G1K etc.: operates normal).
• Refer to the adjustment instruction in the adjustment software for details.
• Refer to the adjustment instruction in the adjustment software for details.
*4
• Confirm self recording/playback motion picture of AVCHD mode by the LCD.
• Confirm it on the TV with HDMI socket when repair HDMI relation.
• Confirm it on the TV with HDMI socket when repair HDMI relation.
* There are no LCD/LVF adjustment model.
*5 NOTE: (When AWB adjustment)
• After change to WB adjustment mode for service with software, the adjustment is executed.
After adjusting the AWB adjustment, to cancel the WB adjustment mode for service.
• Details, refer to the instructions in the adjustment software.
About the 3D interchangeable lens (H-FT012) correspondence
This unit has no special structure (circuit or part) for the 3D interchangeable lens correspondence, only by software is processed
the 3D interchangeable lens correspondence.
Therefore, if taken with other lenses as usual, the 3D interchangeable lens is no problem for operation.
the 3D interchangeable lens correspondence.
Therefore, if taken with other lenses as usual, the 3D interchangeable lens is no problem for operation.
50
11 Maintenance
11.1. Notice in external cleaning
11.1.1.
ABOUT THE BODY
NOTE:
Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the SD Memory card and lens unit.
Also, remove the SD Memory card and lens unit.
11.1.1.1. DUST/DIRT ON THE OUTER CASING PART (S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
11.1.1.2. DUST/DIRT ON THE IMAGE SENSOR
1. Blow off the dust on the surface of the Image sensor with the Blower. (Refer to the following Figure.)
• Keep the Mount Facing down condition towards to floor when cleaning.
• Do not put the Blower further inside than the lens mount.
• Be careful not to blow too strongly.
• Do not put the Blower further inside than the lens mount.
• Be careful not to blow too strongly.
2. Wipe off the dirt on the image sensor surface with Lens cleaning KIT(BK)(VFK1900BK).
51
11.1.2.
ABOUT THE LENS
11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
11.1.2.2. DUST/DIRT ON THE LENS GLASSES
• Define the location of the dust/dirt first, whether it is outside
lens surface or not.
1. When it is outside surface of the lens:
• When the dust and/or dirt gets on the outer side sur-
face of the Lens glasses, order the following proce-
dures.
dures.
a. Blow off the dust on the Lens glass surface with
the Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with
Lens cleaning KIT(BK) (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
2. When it is inside of the lens:
• Refer to the “11.2. General description (Lens clean-
ing: Interchangeable Lens/H-H014)”, “11.3. General
description (Lens cleaning: Interchangeable Lens/H-
FS014042)” section of this service manual.
description (Lens cleaning: Interchangeable Lens/H-
FS014042)” section of this service manual.
11.2. General description (Lens cleaning: Interchangeable Lens/H-H014)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
Also do not exchange the 1st lens unit taking from others.
52
11.2.1.
Method of cleaning inside of lens
11.2.1.1. Disassembly procedure
Important:
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
1. Removal of the Decoration Ring
*.Decoration ring is sticked on the 1st lens frame unit.
*.Put the sheet so that the lens glass is fully covered.
*.Insert the needle to Gap “A” (between the Decoration
ring and Lens glass), and peel off the Decoration ring
gentlly.
*.Put the sheet so that the lens glass is fully covered.
*.Insert the needle to Gap “A” (between the Decoration
ring and Lens glass), and peel off the Decoration ring
gentlly.
2. Removal of the 1st Lens frame unit
*.Remove 3 screws (A).
*. Blow off the dust on the surface of the lens with a blower
brush.
*. Use lens cleaning KIT (BK)(VFK1900BK), if necessary.
11.2.1.2. Assembly procedure
IMPORTANT NOTICE:
*.When tightening the screw, use a Torque driver
(RFKZ0456) by ordering the screwing order with specified
torque descrived in each step.
(RFKZ0456) by ordering the screwing order with specified
torque descrived in each step.
1. Installation of the 1st Lens frame unit
*Tighten the 3 screws (A) with specified torgue in
numerical order.
numerical order.
2. Installation of the Decoration ring
*Install the Decoration ring by referring the phase mark.
(Use new one, Do not use the one which is removed.)
(Use new one, Do not use the one which is removed.)
* After installing the Decoration ring, press the decoration ring
with your finger.
Click on the first or last page to see other DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT service manuals if exist.