Panasonic DMC-G3KEE Service Manual ▷ View online
41
(Fig. D21)
9.1.3.15. Removal of the LCD IF P.C.B.
(Fig. D22)
42
9.1.3.16. Removal of the LCD Unit
(Fig. D23)
NOTE: (When Installing)
Make sure to confirm the following points when installing:
• The Screw is tightened enough.
• Installing conditions are fine. (No distortion, no abnormal-
• Installing conditions are fine. (No distortion, no abnormal-
space.)
• No dust and/or dirt on Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
43
9.2.
Disassembly and Assemble Procedure for the Lens (H-FS014042)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. K1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the “11 Maintenance” for detailes.
As for procedure, refer to the “11 Maintenance” for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. K1.
NOTE:
NOTE:
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, men-
tioned on the above table.
2. The Ref.B213 is no need to remove/install for disassembly and assembly.
If necessary, use VFK1390 (small driver) when screwing it.
Interchangeable Lens (H-FS014042)
(Fig. K1)
44
9.3.
Disassembly and Assemble Procedure for the Lens (H-FS045200)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. W1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the “11 Maintenance” for detailes.
As for procedure, refer to the “11 Maintenance” for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. W1.
NOTE:
NOTE:
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, men-
tioned on the above table.
2. The Ref.B309 is no need to remove/install for disassembly and assembly.
3. Use small driver (VFK1390) when removing/tighten the B308.
3. Use small driver (VFK1390) when removing/tighten the B308.
Interchangeable Lens (H-FS045200)
(Fig. W1)
Click on the first or last page to see other DMC-G3KEE service manuals if exist.