DOWNLOAD Panasonic DMC-G3KEE Service Manual ↓ Size: 8.05 MB | Pages: 81 in PDF or view online for FREE

53

When tightening the screw, use a torque driver (RFKZ0456)
by ordering the screwing order with specified torque
described in each step. 

1. Install the 1st lens frame unit onto the lens unit to meet

the through hole (A) with projection (A).

2. Tighten the 3 screws (A) with specified torque in numeri-

cal order.
(Torque Driver: RFKZ0456)
(Torque: 14.7 ± 1.0 N-cm)

54

1. Use the Name Ring fixture (RFKZ0507)
2. Use new Decoration ring. (Do not use the one which is

removed.)

S-1

S1. About Indication of The Schematic Diagram ............................ S-1

S1.1. Important Safety Notice......................................................... S-1

S2. Voltage Chart ........................................................................... S-2

S2.1. Flash P.C.B. .......................................................................... S-2

S3. Block Diagram .......................................................................... S-3

S3.1. Overall Block Diagram .......................................................... S-3

S4. Schematic Diagram .................................................................. S-4

S4.1. Interconnection Diagram ....................................................... S-4

S4.2. Top Operation Schematic Diagram ....................................... S-5

S4.3. Flash Schematic Diagram ..................................................... S-6

S4.4. Rear Operation Schematic Diagram ..................................... S-7

S4.5. MIC Schematic Diagram ....................................................... S-8

S5. Print Circuit Board .................................................................... S-9

S5.1. Top P.C.B. ............................................................................. S-9

S5.2. Flash P.C.B. ........................................................................ S-10

S5.3. Rear Operation P.C.B. ......................................................... S-11

S5.4. MIC P.C.B. ........................................................................... S-12

S6. Replacement Parts List .......................................................... S-13

S7. Exploded View ....................................................................... S-22

S7.1. Frame and Casing Section.................................................. S-22

S7.2. Camera Lens Section (1) .................................................... S-23

S7.3. Camera Lens Section (2) .................................................... S-24

S7.4. Packing Parts and Accessories Section (1) ........................ S-25

S7.5. Packing Parts and Accessories Section (2) ........................ S-26

S7.6. Packing Parts and Accessories Section (3) ........................ S-27

DSC1106032CE

Model No.

Digital Camera/Lens Kit/

Double Zoom Lens Kit/Body

Name of Signal

OFTR

FEP

This signal is connected

to the FEP schematic diagram.

Circuit name being connected.

6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:

5.The voltage being indicated here may be include observational-error (deviation) due to

internal-resistance and/or reactance of equipment. Therefore, handle the value

indicated on here as reference.

4.Although the voltage and waveform available on here is measured with standard frame,

it may be differ from actual measurement due to modification of circuit and so on.

3.The voltage being indicated on the schematic diagram is measured in

"Standard-Playback" mode when there is no specify mode is mentioned.

2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.

when the TP (Test Point) indicated as " " mark.

1.Although reference number of the parts is indicated on the P.C.B. drawing and/or

schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.

FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.

COMPONENTS IDENTIFIED WITH THE MARK

HAVE THE SPECIAL CHARACTERISTICS

DMC-G3KPP

DMC-G3KPC

DMC-G3KEB

DMC-G3KEC

DMC-G3KEE

DMC-G3KEG

DMC-G3KGC

DMC-G3KGD

DMC-G3KGH

DMC-G3KGK

DMC-G3KGN

DMC-G3KGT

DMC-G3PP

DMC-G3PC

DMC-G3EB

DMC-G3EC

DMC-G3EE

DMC-G3EG

DMC-G3GC

DMC-G3GD

DMC-G3GH

DMC-G3GN

DMC-G3GT

DMC-G3WPP

DMC-G3WEB

DMC-G3WEC

DMC-G3WEE

DMC-G3WEG

DMC-G3WGC

DMC-G3WGD

DMC-G3WGH

DMC-G3WGK

DMC-G3WGN

DMC-G3WGT

Vol. 1

[DMC-G3K]

Colour

(K)........Black Type

(R)...........Red Type (except GD/GT)

(T)...........Brown Type (only PP/EG/GC)

(W)..........White Type (except PC/EG)

(K)........Black Type

(R)...........Red Type (except PP/EE/GD/GT)

(T)...........Brown Type (only EG/GC)

(KA).........Black Type (only EB)

(W)..........White Type (except PP/EB/EE/EG)

[DMC-G3W]

(K)........Black Type

DMC-G3K series: Interchangeable Lens (H-FS014042) is bundled.

DMC-G3W series: Interchangeable Lens (H-FS014042/H-FS045200) are bundled.

DMC-G3 series: Camera Body Only.

[DMC-G3]

Table of contents

S-2

Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. 

          Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. 

REF No.

PIN No. POWER ON

Q8502

1

7.8

Q8502

2

7.8

Q8502

3

0

Q8502

4

0

Q8502

5

7.8

Q8502

6

7.8

QR8501

1

0

QR8501

2

4.5

QR8501

3

0

QR8501

4

4.8

QR8501

5

4.5

QR8501

6

0

QR8502

E

0

QR8502

C

4.5

QR8502

B

0