Panasonic DMC-FX77EB / DMC-FX77EE / DMC-FX77EF / DMC-FX77EG / DMC-FX77EP / DMC-FX77SG / DMC-FX78P / DMC-FX78PU / DMC-FX78GC / DMC-FX78GD / DMC-FX78GH / DMC-FX78GK / DMC-FX78GN / DMC-FX78GT Service Manual ▷ View online
17
[Rec] Mode:
Ç
Taking pictures using the Touch Shutter function
Just by touching the subject to focus, it will focus on the subject and take the picture
automatically.
automatically.
Touch [
].
Icon will change to [
], and taking a picture with the
Touch Shutter function becomes possible.
Touch the subject you wish to
focus on, and then take a picture.
AF area with same function as [
®] in AF Mode is displayed at the position you touch, and
a picture is taken when it is focused. (It cannot be set to edge of the screen)
Touch [
] to cancel the Touch Shutter function.
×
[Rec] Mode:
Ç
Recording Motion Pictures
This can record full high definition motion pictures compatible with the AVCHD format or
motion pictures recorded in Motion JPEG.
Audio will be recorded in monaural.
motion pictures recorded in Motion JPEG.
Audio will be recorded in monaural.
Start recording by pressing the motion
picture button.
Available recording time
Elapsed recording time
Elapsed recording time
You can record motion pictures fitting each
Recording Mode.
Recording Mode.
Release the motion picture button right after you
press it.
press it.
The recording state indicator (red)
will flash while
recording motion pictures.
Stop the recording by pressing the motion picture button again.
18
6 Service Mode
6.1.
Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to FLASH-ROM when the unit has just before powered off.
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to FLASH-ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
• Preparation:
a. Attach the Battery or AC Adaptor with a DC coupler to the unit.
b. Slide the lend cover fully downward and turn off the power by pressing the power button which is located on the top
b. Slide the lend cover fully downward and turn off the power by pressing the power button which is located on the top
case unit.
NOTE:
*Since this unit has built-in memory, it can be performed without inserting SD memory card.
*Since this unit has built-in memory, it can be performed without inserting SD memory card.
• Step 1. The temporary cancellation of “INITIAL SETTINGS”:
While pressing “W side of [ ZOOM LEVER ]”, [ SHUTTER BUTTON ] and touch the screen (Any position of the screen is
acceptable) simultaneously, turn the power on.
acceptable) simultaneously, turn the power on.
• Step 2. Execute the error code display mode:
Display [ Version Disp. ] screen in the state of Step 1, and then move the [ ZOOM LEVER ] to “W” side.
The display is changed as shown below when the moving to W side.
Version Disp.
The display is changed as shown below when the moving to W side.
Version Disp.
→ Error code display → Operation history display → Version Disp. → .....
Example of Error Code Display
19
• 3. Error Code List
The error code consists of 8 bits data and it shows the following information.
20
Important notice about "Error Code List"
1) About "*" indication:
The third digit from the left is different as follows.
1) About "*" indication:
The third digit from the left is different as follows.
- In case of 0 (example: 18001000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been
completed.
It means that this error is occurred basically at user side.
completed.
It means that this error is occurred basically at user side.
- In case of 8 (example: 18801000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
• 4. How to exit from Error Code display mode:
Simply, turn the power off. (Since Error code display mode is executed under the condition of temporary cancellation of "INI-
TIAL SETTINGS", it wake up with normal condition when turn off the power.)
TIAL SETTINGS", it wake up with normal condition when turn off the power.)
NOTE:
The error code can not be initialized.
Click on the first or last page to see other DMC-FX77EB / DMC-FX77EE / DMC-FX77EF / DMC-FX77EG / DMC-FX77EP / DMC-FX77SG / DMC-FX78P / DMC-FX78PU / DMC-FX78GC / DMC-FX78GD / DMC-FX78GH / DMC-FX78GK / DMC-FX78GN / DMC-FX78GT service manuals if exist.