Panasonic DMC-FX50PP / DMC-FX50PL / DMC-FX50EB / DMC-FX50EE / DMC-FX50EF / DMC-FX50EG / DMC-FX50EGM / DMC-FX50GC / DMC-FX50GD / DMC-FX50GK / DMC-FX50GN / DMC-FX50GT / DMC-FX50SG Service Manual ▷ View online
21
8.3.
Disassembly Procedure
8.3.1.
Removal of the Rear Case Unit
Fig. D1
No.
Item
Fig
Removal
1
Rear Case Unit
Fig. D1
Card
Battery
2 Screws (A)
3 Screws (B)
Side Ornament (R)
Side Ornament (L)
Battery
2 Screws (A)
3 Screws (B)
Side Ornament (R)
Side Ornament (L)
Fig. D2
FP9001(Flex)
FP9002(Flex)
Rear Case Unit
FP9002(Flex)
Rear Case Unit
2
LCD Unit
Fig. D3
2 Locking tabs
LCD Unit
LCD Unit
3
Front Case Unit
Fig. D4
1 Screw (C)
3 Screws (D)
Tripod Fixing Plate
2 Locking tabs
Front Case Unit
3 Screws (D)
Tripod Fixing Plate
2 Locking tabs
Front Case Unit
4
Top Operation Unit
Fig. D5
2 Locking tabs
PS8001(Connector)
Top Operation Unit
PS8001(Connector)
Top Operation Unit
5
Flash Top P.C.B.
Fig. D6
2 Screws (E)
6 Locking tabs
Top Operation Unit
Power knob
P8001(Connector)
Flash Cover
Flash Top P.C.B.
6 Locking tabs
Top Operation Unit
Power knob
P8001(Connector)
Flash Cover
Flash Top P.C.B.
6
Main P.C.B.
Fig. D7
PP9001(Connector)
Main P.C.B.
Main P.C.B.
7
Lens Unit
Fig. D8
FP9801(Flex)
FP9802(Flex)
1 Locking tab
Lens Unit
FP9802(Flex)
1 Locking tab
Lens Unit
8
Sub P.C.B.
Fig. D9
1 Screw (F)
1 Locking tab
PCB Spacer
Joystick Knob
Joy Cover
Sub P.C.B.
1 Locking tab
PCB Spacer
Joystick Knob
Joy Cover
Sub P.C.B.
9
Battery Case
Fig. D10
Frame
2 Locking tabs
Battery Case
2 Locking tabs
Battery Case
22
Fig. D2
8.3.2.
Removal of the LCD Unit
Fig. D3
8.3.3.
Removal of the Front Case Unit
Fig. D4
8.3.4.
Removal of the Top Operation Unit
Fig. D5
23
8.3.5.
Removal of the Flash Top P.C.B.
Fig. D6
8.3.6.
Removal of the Main P.C.B.
Fig. D7
8.3.7.
Removal of the Lens Unit
Fig. D8
24
8.3.8.
Removal of the Sub P.C.B.
Fig. D9
8.3.9.
Removal of the Battery Case
Fig. D10
NOTE: (When Assembling)
Be sure to confirm the following points when assembling.
• The Screw is tightened enough.
• Assembling conditions are fine. (No distortion, no illegal-
• Assembling conditions are fine. (No distortion, no illegal-
space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
8.4.
Disassembly Procedure for the
Lens
Lens
NOTE: When Disassembling and Assembling for the Lens
1. To minimize the possibility of the CCD being dirt, perform
disassemble and/or assemble under the condition of the
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
2. Take care that the dust and dirt are not entered into the
lens.
In case of the dust is putted on the lens, blow off them by
airbrush.
In case of the dust is putted on the lens, blow off them by
airbrush.
3. Do not touch the surface of lens.
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (VFK1829) to the point where is shown
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (VFK1829) to the point where is shown
to" Grease apply" in the figure.
When the grease is applied, use a toothpick and apply
thinly.
When the grease is applied, use a toothpick and apply
thinly.
8.4.1.
Zoom Motor Unit, Master Frange
Unit, Drive/Direct Frame Unit and
1st Lens Frame/2nd Lens Frame
Move Unit
Unit, Drive/Direct Frame Unit and
1st Lens Frame/2nd Lens Frame
Move Unit
1. Unscrew the 4 screws (A).
2. Remove the zoom motor unit to the indicated by arrow.
3. Remove the master frange unit to the indicated by arrow.
2. Remove the zoom motor unit to the indicated by arrow.
3. Remove the master frange unit to the indicated by arrow.
Click on the first or last page to see other DMC-FX50PP / DMC-FX50PL / DMC-FX50EB / DMC-FX50EE / DMC-FX50EF / DMC-FX50EG / DMC-FX50EGM / DMC-FX50GC / DMC-FX50GD / DMC-FX50GK / DMC-FX50GN / DMC-FX50GT / DMC-FX50SG service manuals if exist.