Panasonic DMC-FX500P / DMC-FX500PC / DMC-FX500PL / DMC-FX500E / DMC-FX500EB / DMC-FX500EE / DMC-FX500EF / DMC-FX500EG / DMC-FX500SG / DMC-FX520GC / DMC-FX520GD / DMC-FX520GK / DMC-FX520GN / DMC-FX520GT / DMC-FX520GJ / DMC-FX500EES / DMC-FX500EEK Service Manual ▷ View online
25
8.3.8.
Removal of the Main P.C.B.
Fig. D9
8.3.9.
Removal of the SD FPC Unit
Fig. D10
8.3.10.
Removal of the Battery Case Unit
Fig. D11
8.3.11.
Removal of the Jack Door
Fig. D12
26
8.3.12.
Removal of the Battery Door Unit
Fig. D13
NOTE: (When Assembling)
Be sure to confirm the following points when assembling.
• The Screw is tightened enough.
• Assembling conditions are fine. (No distortion, no illegal-
• Assembling conditions are fine. (No distortion, no illegal-
space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
8.4.
Disassembly Procedure for the
Lens
Lens
NOTE: When Disassembling and Assembling for the Lens
1. To minimize the possibility of the CCD being dirt, perform
disassemble and/or assemble under the condition of the
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
2. Take care that the dust and dirt are not entered into the
lens.
In case of the dust is putted on the lens, blow off them by
airbrush.
In case of the dust is putted on the lens, blow off them by
airbrush.
3. Do not touch the surface of lens.
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (RFKZ0472) to the point where is
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (RFKZ0472) to the point where is
shown to" Grease apply" in the figure.
When the grease is applied, use a toothpick and apply
thinly.
When the grease is applied, use a toothpick and apply
thinly.
6. When repair the drive frame, direct frame and fixed
frame, must be unit exchange.
27
8.4.1.
Removal of the Zoom Motor Unit
and Lens FPC P.C.B. Unit
and Lens FPC P.C.B. Unit
1. Remove the 1 solder (A).
2. Remove the 1 solder (B).
3. Unscrew the 2 screws (A).
4. Unscrew the 1 screw (B).
5. Remove the 2 locks.
6. Remove the zoom motor unit to the indicated by arrow
2. Remove the 1 solder (B).
3. Unscrew the 2 screws (A).
4. Unscrew the 1 screw (B).
5. Remove the 2 locks.
6. Remove the zoom motor unit to the indicated by arrow
(1).
7. Remove the lens FPC P.C.B. unit to the indicated by
arrow (2).
8.4.2.
Removal of the Master Flange Unit
28
8.4.3.
Removal of the 1st Lens Frame/2nd
Lens Frame Move Unit
Lens Frame Move Unit
8.4.4.
Removal of the 2nd Lens Frame
Move Unit
Move Unit
8.5.
Assembly Procedure for the
Lens
Lens
8.5.1.
Phase alignment of the Direct
Frame and Drive Frame Unit
Frame and Drive Frame Unit
Click on the first or last page to see other DMC-FX500P / DMC-FX500PC / DMC-FX500PL / DMC-FX500E / DMC-FX500EB / DMC-FX500EE / DMC-FX500EF / DMC-FX500EG / DMC-FX500SG / DMC-FX520GC / DMC-FX520GD / DMC-FX520GK / DMC-FX520GN / DMC-FX520GT / DMC-FX520GJ / DMC-FX500EES / DMC-FX500EEK service manuals if exist.