DOWNLOAD Panasonic DMC-FT3EB / DMC-FT3EE / DMC-FT3EF / DMC-FT3EG / DMC-FT3EP / DMC-FT3GC / DMC-FT3GN / DMC-FT3SG / DMC-TS3P / DMC-TS3PC / DMC-TS3PU / DMC-TS3GH / DMC-TS3GD / DMC-TS3GT Service Manual ↓ Size: 6.61 MB | Pages: 75 in PDF or view online for FREE

25

3. Error Code List

The error code consists of 8 bits data and it shows the following information.

Attribute

Main item

Sub item

Error code

Contents (Upper)

Error Indication

High 4bits Low 4 bits

Check point (Lower)

Detecting

device

Part/Circuit

LENS

Lens drive OIS

18*0

1000

PSD (X) error. Hall element (X axis) position detect
error in OIS unit.

OIS X

LENSu NG

OIS Unit

2000

PSD (Y) error. Hall element (Y axis) position detect
error in OIS unit.

OIS Y

OIS Unit

3000

GYRO (X) error. Gyro (IC6301) detect error on Top
P.C.B.

GYRO X

GYRO NG

IC6301 (Gyro element) or IC6001 (VENUS FHD)

4000

GYRO (Y) error. Gyro (IC6302) detect error on Top
P.C.B.

GYRO Y

IC6302 (Gyro element) or IC6001 (VENUS FHD)

5000

MREF error (Reference voltage error).

OIS REF

LENSSd/DSP 

NG

IC9101 (LENS DRIVE) or IC6001 (VENUS FHD)

6000

Drive voltage (X) error.

OISX REF

LENSu/LENS 

FPC

LENS Unit, LENS flex breaks, IC6001(VENUS FHD)
AD value error, etc.

7000

Drive voltage (Y) error.

OISY REF

LENS Unit, LENS flex breaks, IC6001(VENUS FHD)
AD value error, etc.

Zoom

0?10

Collapsible barrel Low detect error
(Collapsible barrel encoder always detects Low.)

ZOOM L

ZOOMm/

LENSu

Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS FHD)

0?20

Collapsible barrel High detect error
(Collapsible barrel encoder always detects High.)

ZOOM H

Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS FHD)

0?60

The zoom position jump is detected due to the
impact (i.e. drop.) to the camera occurs.

(No indication) (No indication)

Lens unit

Focus

0?01

HP High detect error
(Focus encoder always detects High, and not
becomes Low)

FOCUS L

LENS FPC/

DSP

Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS FHD)

0?02

HP Low detect error
(Focus encoder always detects Low, and not
becomes High)

FOCUS H

Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS FHD)

Lens

18*1

0000

Power ON time out error.

LENS DRV

LENSu

Lens drive system

18*2

0000

Power OFF time out error.
Lens drive system

Adj.History OIS

19*0

2000

OIS adj. Yaw direction amplitude error (small)

OIS ADJ

OIS ADJ

3000

OIS adj. Pitch direction amplitude error (small)

4000

OIS adj. Yaw direction amplitude error (large)

5000

OIS adj. Pitch direction amplitude error (large)

6000

OIS adj. MREF error

7000

OIS adj. time out error

8000

OIS adj. Yaw direction off set error

9000

OIS adj. Pitch direction off set error

A000

OIS adj. Yaw direction gain error

B000

OIS adj. Pitch direction gain error

C000

OIS adj. Yaw direction position sensor error

D000

OIS adj. Pitch direction position sensor error

E000

OIS adj. other error

26

1) About "*" indication:
 The third digit from the left is different as follows.
 In case of 0 (example: 18 0 01000)
  When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed.
  It means that this error is occurred basically at user side.
 In case of 8 (example: 18 8 01000)
  When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been released.                 
  (Example; Factory assembling-line before unit shipment, Service mode etc.)                 
  It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):                 
 The third digit from the right shows one of the hexadecimal ("0" to "F") character.

4. How to returned to Normal Display:
 Turn the power off and on, to exit from Error code display mode.
Note:

The error code can not be initialized.

HARD

VENUS A/
D

Flash

28*0

0000

Flash charging error.

STRB CHG

FLASH P.C.B./

FPC

IC6001-(AC16) signal line or Flash charging circuit

FLASH
ROM
(EEPROM
Area)

FLASH
ROM
(EEPROM
Area)

2B*0

0001
0003
0004

EEPROM read error

FROM RE

FROM

IC6002 (FLASH ROM)

0002

EEPROM write error

FROM WR

FROM

IC6002 (FLASH ROM)

0005

Firmware version up error

(No indication) (No indication)

Replace the firmware file in the SD memory card.

0008

SDRAM error

0009

SDRAM Mounting defective

SYSTEM

RTC

2C*0

0001

SYSTEM IC initialize failure error

SYS INIT

MAIN P.C.B.

Communication between IC6001 (VENUS FHD) and
IC9101 (SYSTEM)

SOFT

CPU

Reset

30*0

0001

|

0007

NMI reset
Non Mask-able Interrupt
(30000001-30000007 are caused by factors)

NMI RST

MAIN P.C.B.

Card

Card

31*0

0001

Card logic error

SD CARD

SD CARD/

DSP

SD memory card data line or IC6001 (VENUS FHD)

0002

Card physical error
SD memory card data line or IC6001 (VENUS FHD)

0004

Write error

SD WRITE

SD memory card data line or IC6001 (VENUS FHD)

39*0

0005

Format error

INMEMORY

FROM

CPU,
ASIC hard

Stop

38*0

0001

Camera task finish process time out.

LENS COM

LENSu/DSP

Communication between Lens system and IC6001
(VENUS FHD)

0002

Camera task invalid code error.

DSP

DSP

IC6001 (VENUS FHD)

0100

File time out error in recording motion image
IC6001 (VENUS FHD)

0200

File data cue send error in recording motion image
IC6001 (VENUS FHD)

0300

Single or burst recording brake time out.

Memory
area

3A*0

0008

USB work area partitioning failure

(No indication) (No indication)

USB dynamic memory securing failure when con-
necting

Operation

Power on

3B*0

0000

FLASHROM processing early period of camera dur-
ing movement.

INIT

(No indication)

Zoom

Zoom

3C*0

0000

Imperfect zoom lens processing

ZOOM

ZOOMm/

LENSu

Zoom lens

35*0

0000

|

FFFF

Software error
(0-7bit : command, 8-15bit : status)

DSP

DSP

35*1

0000

Though record preprocessing is necessary, it is not
called.

35*2

0000

Though record preprocessing is necessary, it is not
completed.

(No indication) (No indication)

Attribute

Main item

Sub item

Error code

Contents (Upper)

Error Indication

High 4bits Low 4 bits

Check point (Lower)

Detecting

device

Part/Circuit

27

This unit is equipped with ICS (ICS：Indication of additional Camera Settings when picture was taken) function by playing back the
concerned picture on the LCD display.
(This function is achieved by utilizing "maker note" data stored in Exif data area of recorded picture file.)
To proceed failure diagnosis, use this ICS function together with "displaying the recorded picture with picture information" function. 
Note:

*.The ICS function operates with a picture which is only taken with the same model. (It may not be displayed when the picture 
   was taken with other model.)
*.Since Exif data is not available after the picture is edited by PC, the ICS function may not be activated.

2. How to display
The ICS data is displayed by ordering the following procedure:

• Preparation:

1.Attach the Battery or AC Adaptor with a DC coupler to the unit.
 Note:

*Select the mode other than "3D "mode (such as normal picture / iA / Sports / Snow / SCN) to display the ICS data.

• Step 1. The temporary cancellation of "INITIAL SETTINGS":

While keep pressing "UP of Cursor button" and MOTION PICTURE button simultaneously, turn the Power on.

• Step 2. Execute the ICS display mode:

Press the PLAYBACK button.
Select the concerned picture by pressing the "LEFT and RIGHT of Cursor button".
Press the "LEFT of Cursor button", MENU/SET button and MOTION PICTURE button simultaneously.
Press the DISPLAY button, 3 times.
The display condition is changed as shown below when the DISPLAY button is pressed.
Code display 

→ Code + Picture display (1) → Code + Picture display (2) → ICS display → .....

28

4. How to exit
Simply, turn the power off. (Since ICS function is executed under the condition of temporary cancellation of "INITIAL SETTINGS",it
wake up with normal condition when turn off the power.)