Panasonic DMC-FT2EB / DMC-FT2EE / DMC-FT2EF / DMC-FT2EG / DMC-FT2EP / DMC-FT2GC / DMC-FT2GN / DMC-FT2SG / DMC-TS2P / DMC-TS2PC / DMC-TS2PU / DMC-TS2GH / DMC-TS2GD / DMC-TS2GT Service Manual ▷ View online
25
6 Service Mode
6.1.
Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to FLASH ROM when the unit has just before powered off.
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to FLASH ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
• Preparation:
1. Attach the Battery or AC Adaptor with a DC coupler to the unit.
Note:
*Since this unit has built-in memory, it can be performed without inserting SD memory card.
*Set the mode dial other than "CLIPBOARD (memo)" mode (such as normal picture / iA / Sports / Snow / SCN)
*Set the mode dial other than "CLIPBOARD (memo)" mode (such as normal picture / iA / Sports / Snow / SCN)
to display the error code.
• Step 1. The temporary cancellation of "INITIAL SETTINGS":
While keep pressing "UP of Cursor button" and DISPLAY button simultaneously, turn the Power on.
• Step 2. Execute the error code display mode:
Press the "LEFT of Cursor button", MENU/SET button and DISPLAY button simultaneously.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display
→ Error code display → Operation history display → Normal display → .....
26
3. Error Code List
The error code consists of 8 bits data and it shows the following information.
Attribute
Main item
Sub item
Error code
Contents (Upper)
Error Indication
High 4bits Low 4 bits
Check point (Lower)
Detecting
device
Part/Circuit
LENS
Lens drive OIS
18*0
1000
PSD (X) error. Hall element (X axis) position detect
error in OIS unit.
error in OIS unit.
OIS X
LENSu NG
OIS Unit
2000
PSD (Y) error. Hall element (Y axis) position detect
error in OIS unit.
error in OIS unit.
OIS Y
OIS Unit
3000
GYRO (X) error. Gyro (IC6301) detect error on Top
P.C.B.
P.C.B.
GYRO X
GYRO NG
IC6301 (Gyro element) or IC6001 (VENUS HD2)
4000
GYRO (Y) error. Gyro (IC6302) detect error on Top
P.C.B.
P.C.B.
GYRO Y
IC6302 (Gyro element) or IC6001 (VENUS HD2)
5000
MREF error (Reference voltage error).
OIS REF
LENSSd/DSP
NG
IC9101 (LENS DRIVE) or IC6001 (VENUS HD2)
6000
Drive voltage (X) error.
OISX REF
LENSu/LENS
FPC
LENS Unit, LENS flex breaks, IC6001(VENUS HD2)
AD value error, etc.
AD value error, etc.
7000
Drive voltage (Y) error.
OISY REF
LENS Unit, LENS flex breaks, IC6001(VENUS HD2)
AD value error, etc.
AD value error, etc.
Zoom
0?10
Collapsible barrel Low detect error
(Collapsible barrel encoder always detects Low.)
(Collapsible barrel encoder always detects Low.)
ZOOM L
ZOOMm/
LENSu
Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS HD2)
(VENUS HD2)
0?20
Collapsible barrel High detect error
(Collapsible barrel encoder always detects High.)
(Collapsible barrel encoder always detects High.)
ZOOM H
Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS HD2)
(VENUS HD2)
0?60
The zoom position jump is detected due to the
impact (i.e. drop.) to the camera occurs.
impact (i.e. drop.) to the camera occurs.
(No indication) (No indication)
Lens unit
Focus
0?01
HP High detect error
(Focus encoder always detects High, and not
becomes Low)
(Focus encoder always detects High, and not
becomes Low)
FOCUS L
LENS FPC/
DSP
Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS HD2)
(VENUS HD2)
0?02
HP Low detect error
(Focus encoder always detects Low, and not
becomes High)
(Focus encoder always detects Low, and not
becomes High)
FOCUS H
Mechanical lock, FP9002-(40) signal line or IC6001
(VENUS HD2)
(VENUS HD2)
Lens
18*1
0000
Power ON time out error.
LENS DRV
LENSu
Lens drive system
18*2
0000
Power OFF time out error.
Lens drive system
Lens drive system
Adj.History OIS
19*0
2000
OIS adj. Yaw direction amplitude error (small)
OIS ADJ
OIS ADJ
3000
OIS adj. Pitch direction amplitude error (small)
4000
OIS adj. Yaw direction amplitude error (large)
5000
OIS adj. Pitch direction amplitude error (large)
6000
OIS adj. MREF error
7000
OIS adj. time out error
8000
OIS adj. Yaw direction off set error
9000
OIS adj. Pitch direction off set error
A000
OIS adj. Yaw direction gain error
B000
OIS adj. Pitch direction gain error
C000
OIS adj. Yaw direction position sensor error
D000
OIS adj. Pitch direction position sensor error
E000
OIS adj. other error
27
1) About "*" indication:
The third digit from the left is different as follows.
In case of 0 (example: 18 0 01000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed.
It means that this error is occurred basically at user side.
In case of 8 (example: 18 8 01000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
The third digit from the left is different as follows.
In case of 0 (example: 18 0 01000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed.
It means that this error is occurred basically at user side.
In case of 8 (example: 18 8 01000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
4. How to returned to Normal Display:
Turn the power off and on, to exit from Error code display mode.
Note:
Turn the power off and on, to exit from Error code display mode.
Note:
The error code can not be initialized.
HARD
VENUS A/
D
D
Flash
28*0
0000
Flash charging error.
STRB CHG
FLASH P.C.B./
FPC
IC6001-(AC16) signal line or Flash charging circuit
FLASH
ROM
(EEPROM
Area)
ROM
(EEPROM
Area)
FLASH
ROM
(EEPROM
Area)
ROM
(EEPROM
Area)
2B*0
0001
0003
0004
0003
0004
EEPROM read error
FROM RE
FROM
IC6002 (FLASH ROM)
0002
EEPROM write error
FROM WR
FROM
IC6002 (FLASH ROM)
0005
Firmware version up error
(No indication) (No indication)
Replace the firmware file in the SD memory card.
0008
SDRAM error
0009
SDRAM Mounting defective
SYSTEM
RTC
2C*0
0001
SYSTEM IC initialize failure error
SYS INIT
MAIN P.C.B.
Communication between IC6001 (VENUS HD2) and
IC9101 (SYSTEM)
IC9101 (SYSTEM)
SOFT
CPU
Reset
30*0
0001
|
0007
NMI reset
Non Mask-able Interrupt
(30000001-30000007 are caused by factors)
Non Mask-able Interrupt
(30000001-30000007 are caused by factors)
NMI RST
MAIN P.C.B.
Card
Card
31*0
0001
Card logic error
SD CARD
SD CARD/
DSP
SD memory card data line or IC6001 (VENUS HD2)
0002
Card physical error
SD memory card data line or IC6001 (VENUS HD2)
SD memory card data line or IC6001 (VENUS HD2)
0004
Write error
SD WRITE
SD memory card data line or IC6001 (VENUS HD2)
39*0
0005
Format error
INMEMORY
FROM
CPU,
ASIC hard
ASIC hard
Stop
38*0
0001
Camera task finish process time out.
LENS COM
LENSu/DSP
Communication between Lens system and IC6001
(VENUS HD2)
(VENUS HD2)
0002
Camera task invalid code error.
DSP
DSP
IC6001 (VENUS HD2)
0100
File time out error in recording motion image
IC6001 (VENUS HD2)
IC6001 (VENUS HD2)
0200
File data cue send error in recording motion image
IC6001 (VENUS HD2)
IC6001 (VENUS HD2)
0300
Single or burst recording brake time out.
Memory
area
area
3A*0
0008
USB work area partitioning failure
(No indication) (No indication)
USB dynamic memory securing failure when con-
necting
necting
Operation
Power on
3B*0
0000
FLASHROM processing early period of camera dur-
ing movement.
ing movement.
INIT
(No indication)
Zoom
Zoom
3C*0
0000
Imperfect zoom lens processing
ZOOM
ZOOMm/
LENSu
Zoom lens
35*0
0000
|
FFFF
Software error
(0-7bit : command, 8-15bit : status)
(0-7bit : command, 8-15bit : status)
DSP
DSP
35*1
0000
Though record preprocessing is necessary, it is not
called.
called.
35*2
0000
Though record preprocessing is necessary, it is not
completed.
completed.
(No indication) (No indication)
Attribute
Main item
Sub item
Error code
Contents (Upper)
Error Indication
High 4bits Low 4 bits
Check point (Lower)
Detecting
device
Part/Circuit
28
6.2.
ICS (Indication of additional Camera Settings when picture was taken)
function
function
1. General description
This unit is equipped with ICS (ICS：Indication of additional Camera Settings when picture was taken) function by playing back the
concerned picture on the LCD display.
(This function is achieved by utilizing "maker note" data stored in Exif data area of recorded picture file.)
To proceed failure diagnosis, use this ICS function together with "displaying the recorded picture with picture information" function.
Note:
concerned picture on the LCD display.
(This function is achieved by utilizing "maker note" data stored in Exif data area of recorded picture file.)
To proceed failure diagnosis, use this ICS function together with "displaying the recorded picture with picture information" function.
Note:
*.The ICS function operates with a picture which is only taken with the same model. (It may not be displayed when the picture
was taken with other model.)
*.Since Exif data is not available after the picture is edited by PC, the ICS function may not be activated.
was taken with other model.)
*.Since Exif data is not available after the picture is edited by PC, the ICS function may not be activated.
2. How to display
The ICS data is displayed by ordering the following procedure:
The ICS data is displayed by ordering the following procedure:
• Preparation:
1.Attach the Battery or AC Adaptor with a DC coupler to the unit.
Note:
Note:
*Set the mode dial other than "CLIPBOARD (memo) "mode (such as normal picture / iA / Sports / Snow / SCN) to display the
ICS data.
ICS data.
• Step 1. The temporary cancellation of "INITIAL SETTINGS":
While keep pressing "UP of Cursor button" and DISPLAY button simultaneously, turn the Power on.
• Step 2. Execute the ICS display mode:
Press the PLAYBACK button.
Select the concerned picture by pressing the "LEFT and RIGHT of Cursor button".
Press the "LEFT of Cursor button", MENU/SET button and DISPLAY button simultaneously.
Press the DISPLAY button, 3 times.
The display condition is changed as shown below when the DISPLAY button is pressed.
Code display
Select the concerned picture by pressing the "LEFT and RIGHT of Cursor button".
Press the "LEFT of Cursor button", MENU/SET button and DISPLAY button simultaneously.
Press the DISPLAY button, 3 times.
The display condition is changed as shown below when the DISPLAY button is pressed.
Code display
→ Code + Picture display (1) → Code + Picture display (2) → ICS display → .....
Click on the first or last page to see other DMC-FT2EB / DMC-FT2EE / DMC-FT2EF / DMC-FT2EG / DMC-FT2EP / DMC-FT2GC / DMC-FT2GN / DMC-FT2SG / DMC-TS2P / DMC-TS2PC / DMC-TS2PU / DMC-TS2GH / DMC-TS2GD / DMC-TS2GT service manuals if exist.