Panasonic DMC-FS37EB / DMC-FS37EE / DMC-FS37EG / DMC-FS37EP / DMC-FH27P / DMC-FH27PC / DMC-FH27PR / DMC-FH27PU / DMC-FH27GA / DMC-FH27GC / DMC-FH27GF / DMC-FH27GK / DMC-FH27GN Service Manual ▷ View online
29
8.3.10.
Removal of the Battery Door Unit
and Jack Door
and Jack Door
(Fig. D12)
NOTE: (When Installing)
Make sure to confirm the following points when installing.
• The Screw is tightened enough.
• Installing conditions are fine. (No distortion, no abnormal-
• Installing conditions are fine. (No distortion, no abnormal-
space.)
• No dust and/or dirt on Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
8.4.
Lens Disassembly Procedure
Precaution:
1. Do not remove the CCD when disassembling or re-
assembling the lens in order to maintain it clean.
When remove it, refer to item "8.6.".
When remove it, refer to item "8.6.".
2. Keep dust or dirt away from the lens.
3. To remove dirt or dust from the lens, blow with dry air.
4. Do not touch the lens surface.
5. Apply grease (RFKZ0472) as shown on "THE APPLICA-
3. To remove dirt or dust from the lens, blow with dry air.
4. Do not touch the lens surface.
5. Apply grease (RFKZ0472) as shown on "THE APPLICA-
TION OF GREASE METHOD" in the figure.
6. Apply a light coat of grease using an object similar to a
toothpick.
7. The drive frame unit and penetration cam frame should
be replaced as a unit.
8.4.1.
Removal of the Zoom Motor and
Lens FPC Unit
Lens FPC Unit
1. Remove the 3 tapes.
2. Unscrew the 2 screws (A).
3. Remove the zoom motor to the direction of arrow (1).
4. Unscrew the 1 screw (B).
5. Remove the photo sensor.
6. Remove the 13 solders (A).
7. Remove the 3 solders (B).
8. Remove the 5 locks.
2. Unscrew the 2 screws (A).
3. Remove the zoom motor to the direction of arrow (1).
4. Unscrew the 1 screw (B).
5. Remove the photo sensor.
6. Remove the 13 solders (A).
7. Remove the 3 solders (B).
8. Remove the 5 locks.
30
9. Remove the 4 solders (C).
10. Remove the lens FPC unit to the direction of arrow (3).
8.4.2.
Removal of the Master Flange Unit
1. Unscrew the 4 screws (C).
31
2. Remove the master flange unit.
8.4.3.
Removal of the 1st Lens Frame
Unit/2nd Lens Frame Unit/Both
Sides Cam Frame/2nd 3rd Direct
Frame/3rd Lens Frame Unit
Unit/2nd Lens Frame Unit/Both
Sides Cam Frame/2nd 3rd Direct
Frame/3rd Lens Frame Unit
1. Push the both sides cam frame from the lens front side in
the direction of arrow, and then remove the unit of 1st
lens frame unit/2nd lens frame unit/both sides cam frame/
2nd 3rd direct frame/3rd lens frame unit from the fixed
frame unit/drive frame unit/penetration cam frame/1st
direct frame unit.
lens frame unit/2nd lens frame unit/both sides cam frame/
2nd 3rd direct frame/3rd lens frame unit from the fixed
frame unit/drive frame unit/penetration cam frame/1st
direct frame unit.
32
8.4.4.
Removal of the 2nd Lens Frame
Unit/Both Sides Cam Frame/2nd
3rd Direct Frame/3rd Lens Frame
Unit
Unit/Both Sides Cam Frame/2nd
3rd Direct Frame/3rd Lens Frame
Unit
1. Turn the 2nd lens frame unit/both sides cam frame/2nd
3rd direct frame/3rd lens frame unit in the direction of the
arrow (1) fully, and then remove them in the direction of
the arrow (2).
arrow (1) fully, and then remove them in the direction of
the arrow (2).
8.4.5.
Removal of the 2nd 3rd Direct
Frame
Frame
1. Remove the 2nd 3rd direct frame in the direction of the
arrow.
8.4.6.
Removal of the 3rd Lens Frame
Unit
Unit
1. Remove the 3rd lens frame unit in the direction of the
arrow.
Click on the first or last page to see other DMC-FS37EB / DMC-FS37EE / DMC-FS37EG / DMC-FS37EP / DMC-FH27P / DMC-FH27PC / DMC-FH27PR / DMC-FH27PU / DMC-FH27GA / DMC-FH27GC / DMC-FH27GF / DMC-FH27GK / DMC-FH27GN service manuals if exist.