DOWNLOAD Panasonic WJ-SX150 / WJ-SX150A Service Manual ↓ Size: 3.23 MB | Pages: 55 in PDF or view online for FREE

– 1-1 –

Matrix Switcher WJ-SX

OPERATE

q

0

9

8

7

6

5

4

3

2

1

MODE

UNIT

RESET

w

e

r

1

ON

2 3 4

■

q

Lights up when the power of the unit is turned on.

Note:  The indicator will blink to indicate rising tempera-

ture in the matrix switcher.

w

Reset button (RESET)
Resets and restarts the unit.

Note: The system configuration is not reset.

e

Unit number selector (UNIT)
Normally, set this selector to “0”.
When applying the master-slave connection, set this
selector to one of the following unit numbers.

Master/Slave

Unit number

Master

0

Slave 1

1

Slave 2

2

Slave 3

3

Slave 4

4

r

Mode selector (MODE)
Selects the unit's operation mode.
Normally, set all switches to OFF (NORMAL mode) as
shown in the figure.

Set the switches to this position when you update
the firmware of the unit. (Refer to the operating
instructions of the Multiplexer board.)

This mode is reserved for future use.

1

ON

2 3 4

1

ON

2 3 4

1

ON

2 3 4

NORMAL

SX150 
SOFTWARE UPLOAD

MULTIPLEXER
SOFTWARE UPLOAD

– 1-2 –

■

SIGNAL GND

POWER

AC IN

CAMERA

1

1

2

2

3

3

2

DATA 3 DATA 2

SERIAL

ALARM

TERM

OFF

ON

4

2

1

4

3

EXT OUT

(REC OUT)

CAMERA

SW  IN

RS485(CAMERA)

LINE

SELECT

MONITOR OUT

EXT IN

(PLAY IN)

OUT

IN

4

4

5

5

6

6

7

7

8

8

9

9

10

10

11

11

12

12

13

13

14

14

15

15

16

16

RS485(CAMERA)

PS•DATA

DATA 4

DATA HDR

DATA 1

t

y

u

i

o

!0 !1

!2 !3 !4 !5 !6

!7

!8

t

The video signal connected to the CAMERA IN connec-
tor is supplied at these connectors.
When the power of the matrix switcher is turned off, no
signal is supplied at these connectors.

y

• Connect to cameras or camera site accessories.

These connectors accept either a composite color or
B/W video signal from a camera.
In addition, the VD2 signal to synchronize the vertical
timing of the cameras, and data to control camera site
devices are multiplexed at these connectors.

• When applying the master-slave connection, the func-

tions of connectors will differ.

u

When you connect a PS·Data system controller to the
DATA 4 port, this selector turns the unit's termination
switch to ON/OFF.
The factory default setting is ON.

Note:  When you connect a terminal-mode system con-

troller to the DATA 4 port, set this selector to ON.

i

Connects to alarm sensors.
Accepts the alarm input from the associated alarm sen-
sors.

o

• DATA 1 to 4 connect to the system controller.

DATA 1 to 3 can connect to RS-485 cameras with the
configuration in Administrator Console. DATA 4 can con-
nect to the system controller via the PS·Data protocol.

• DATA HDR connects to a recorder.
• When applying the master-slave connection, the func-

tions of ports will differ.

!0

Connects to a PC for the system configuration through
Administrator Console.

!1

• Connects to an RS-485 camera.

Daisy chain connection is also available.

• When the unit is used as Master in the master-slave

connection, terminal-mode system controllers can be
connected.
Note: To connect terminal-mode controllers, the setting
in SETUP MENU and Administrator Console is required.

!2

Lets you select either full duplex (4 lines) or half duplex
(2 lines) for RS-485 cameras.

!3

This connector is not usable.

!4

This connector is not usable.

!5

A playback or live images from the recorder are supplied
to this connector.

!6

• Connect to monitors.

The video output signals are supplied to the monitors at
these connectors.

• When applying the master-slave connection, the func-

tions of connectors will differ.

!7

Turns the power of the matrix switcher on and off.

!8

To use the unit, plug the power cord (supplied as a stan-
dard accessory) into this socket and connect it to an AC
outlet.

– 2-1 –

1

Function

Master-Slave Connection

N/A

Yes

2

Function

Maximum Camera Connection

16

16 (by 1 unit), 28 (by 2units) ,40 (by 3 units), 
52 (by 4 units), 64 (by 5 units)

3

Function

Connection with WJ-HD200

N/A

Yes

4

SETUP MENU

Master-Slave

N/A

Yes

Administrator Console   

5

SETUP MENU

LCN (Logical Camera Number)

N/A (Fixed to 1-16)

1-99 (Variable)

Administrator Console   

6

SETUP MENU

Tour SEQ

16 steps x 16 patterns

64 steps x 32 patterns

Administrator Console   

7

SETUP MENU

Timer Event

30 events

50 events

 

Administrator Console   

8

SETUP MENU

Alarm Event

16 events

99 events

 

Administrator Console   

9

SETUP MENU

Alarm No. assignment to Alarm port pin

Not variable

Variable

Administrator Console   

10

SETUP MENU 

Controller Name

DATA1-4

Terminal_K1-K4

Administrator Console   

11

SETUP MENU

HD200

N/A

Yes

Administrator Console (Recorder selection item)  

12

Front Panel

Unit Number Selector

1 (Fix)

0 (Normal, Master), 1-4 (Slave)

13

Standard Accessories Cross Cable

None

1

14

Operation

Recoder Selection

[RECORDER]

[0] –> [RECORDER] : Master Recorder

(from Terminal Mode Control Unit.)

[1] –> [RECORDER] : Slave 1 Recorder

[2] –> [RECORDER] : Slave 2 Recorder

[3] –> [RECORDER] : Slave 3 Recorder

[4] –> [RECORDER] : Slave 4 Recorder

15

Operation

Recoder Selection

[1] [1] [1] [CAM]

[1] [0] [0] [CAM] : Master Recorder

(from PS    DATA Control Unit.)

[1] [0] [1] [CAM] : Slave 1 Recorder

[1] [0] [2] [CAM] : Slave 2 Recorder

[1] [0] [3] [CAM] : Slave 3 Recorder

[1] [0] [4] [CAM] : Slave 4 Recorder

8

– 2-2 –

3

8

When replacing the Main Board Ass'y or the Dip Switch

SW4 on the Main Board, set SW4 as shown in Fig. 1.

1
2
3
4
5
6
7
8

O
N

1
2
3
4
5
6
7
8

OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF

1
2
3
4
5
6
7
8

O
N

1
2
3
4
5
6
7
8

ON
ON
OFF
OFF
OFF
OFF
OFF
OFF

3

8

When replacing the Front Board Ass'y or the Dip Switch

SW203 on the Front Board, set SW203 as shown in Fig.

2.

(Component Side)

1

2

3

4

OFF

OFF

OFF

OFF

1

ON

2

3

4