DOWNLOAD Panasonic BB-HCM580CE (serv.man2) Service Manual ↓ Size: 4 MB | Pages: 96 in PDF or view online for FREE

53

1. Attach one camera stand to the bottom of the Light Box and attach the other one to tripod mount at the bottom of the cam-

corder. Next, adjust the height of each camera stand (using coares control) so that the central point of the emission face of the
Light Box aligns with the central point of the camcoder's lens. 

2. Detach the end of the collimator (Infinity Adjustment Lens). Be sure to loosen the Light Box's clipping knob before attaching

the collimator to the Light Box. Screw the end of collomator into the rotary ring one the front of the Light Box to attach.

3. Attach the other end (lens side) of the collimator to the filter mounting screw of the camcorder's Lens. If it dose not fit, use the

step-UP ring provided with the collimator.

4. Load the compact transmission chart (gray-scale/color chart) in the chart holder and insert the chart holder into the chart slot.
5. Connect the DC regulated power supply (DC 12V ±0.2V, Aapprox. 2.0A) to the Light Box using the provided DC cord (red (+),

black (-)) and turn on the power switch at the rear of the Light Box.

6. While shooting the chart with the camcorder, adjust (using fine control) the chart holder posiyion as well as the height of the

Light Box an camcorder until the desired angle of view is achieved.

Camcorder adjustment requires a commercially-available a color temperature conversion filter. For all kinds of thin film filters,
use the provided filter mount. To make a slip-in filter with the desired optical characteristics, follow the procedures below.
To use a slip-in filter, insert i into the Light Box filter slot. It is possible to insert 7 slip-in filters at a time into the filter slot.

* Hint:
Tightening the clipping knob fixes the rotary ring firmly.
When it is completely tightened, the collimator attached to the rotar
ring is at right angles to the emission face of the Light Box or chart.
If the collimator cannot be attached to the camcorder, try tightening
the clipping knob to compensate for shearing of the optical axis in
the collimator.
On the other hand, if the collimator can be attached to the cam-
corder, try loosening the clipping knob slightly to make a little room
around the clipping knob.

<How to Make a Slip-in Filter>

1. Cut the desired optical filter to 45mm~45mm.
2. Remove the seal at the rear of the filter

mount,stick the optical filter in the filter mount
(over the hole), then fold the filter mount in half.

3. It is recommended that you write the filter factor

on the filter mount.

54

Lens Adjustment consists of 2 items below:

•Iris Adjustment
•Zoom Tracking Adjust

Lens Adjustment Program has adjustment modes of individual items and an automatic adjustment mode which adjusts succes-
sively the all items.
(1) Start-up the HCM5 CAMERA Service Tool.
(2) Select Model No. BB-HCM580.
(3) Power on the Set.

•None

1. Connect the Set from PC through LAN.
2. Press the [Iris] button.

•Adjustment completes with no error 

→ Displays “Adjustment OK”

•Adjustment comes out an error 

→ Displays “Adjustment NG”

3. If “Adjustment NG” is displayed, see SECTION 7.6 TROUBLESHOOTING.

•Focus Pattern Chart 
•Collimator
•Light Box

1. Place a ND filter in the HP light box.
2. Attach the focus pattern chart to the collimator.

3. Adjust the set's lens at the same height as the HP light box.

4. With keeping the end of the set's lens inserting into the Collimator, insert the focus chart side of the collimator into the HP light 
box.

5. Connect the Set from PC through LAN to output image.

6. Set the zoom position to TELE and adjust the position so that the Focus Pattern Chart is displayed in the full screen.
7. Press the [Tracking] button.

•Adjustment completes with no error 

→ Displays “Adjustment OK”

•Adjustment comes out an error 

→ Displays “Adjustment NG”

8. If “Adjustment NG” is displayed, see SECTION 7.6 TROUBLESHOOTING.

•Focus Pattern Chart 
•Collimator
•Light Box

1. Set up the HP light box, collimator and the set the same way as 2. Zoom Tracking.
2. Connect the Set from PC through LAN to output image.
3. Set the zoom position to TELE and adjust the position so that the Focus Pattern Chart is display in the full screen.
4. Press the [Auto] button.

•Adjustment completes with no error 

→ Displays “Adjustment OK”

•Adjustment comes out an error 

→ Displays “Adjustment NG”

5. If “Adjustment NG” is displayed, see SECTION 7.6 TROUBLESHOOTING.

55

•Collimator
•Light Box
•Color Chart
•Color Temp. Conversion Filter for 5100K

1. Place the Color Temp. Conversion Filter in the HP light box.
2. Remove the Focus Chart block from the Collimator and attach it with screwing its end into the rotating ring on the front of the

light box.

3. Install the Active-X for the Video Adjustment to the PC.
4. Start-up the HCM5 PTZ CAMERA Service Tool.
5. Select Model No. BB-HCM580.
6. Power on the Set.
7. Execute browser (IE) and open the single camera page.
8. Adjust the set's lens as the same height as the collimator, and perform an image pickup of the inside of the collimator.
9. Press the “Video Adjustment” button.

10. After displaying “Please shoot the Light Box without chart” and adjust the position and zoom range without the Color Chart so

that the White image is displayed in the full screen.

11. Press the “OK” button.

12. Follow the message after displaying dialog. 
13. After displaying “Please shoot Color Chart”, set the Color Chart to HP light box. Adjust the position and zoom range so that

the Color Chart is displayed in the full screen and the target on the screen is placed in the center of each color, as shown in
the following Figure1.

14. Press the “OK” button.
15. When the adjustment completes with no error, the “Adjustment OK” is displayed. 
16. When the adjustment comes out an error, the “Adjustment NG” is displayed.

16-1. When Security Warning window is displayed under the address bar, please execute next steps.
16-2. Click security warning.
16-3. Permit the blocked contents.
16-4. In the case of “Adjustment NG”, see SECTION 7.6 TROUBLESHOOTING.

Collimator must be inserted all the way into light box until reaching stop point. 

• Viewing angle when taking the Color Chart

Figure1

56

BB-HCM580 BLOCK DIAGRAM

SD

Connector

[CN101]

FLASH

(4Mx16bit)

[IC104]

SYSTEM LSI 

(PEGASUS)

[IC102]

RESET  IC

[IC101]

RTC  IC

[IC110]

I/O

Connector

[CN601]

Tr

[Q600/605/606]

VIDEO_OUT

RJ-45

[CN605]

48M

Xtal

[X101]

CAM_CLK

REGULATOR

[IC117]

+1.2V

VDDRTC

SDRAM

(8M x 16bit x 2)

[IC103/106]

CAMD[11:2]

32kXtal

[X103]

25M Xtal

[X102]

Ether PHY IC

[IC105]

MII

SD LED

[LED101]

Tr

Q106

FUNCTION

BUTTON [SW103]

CLEAR SETTING

SWICH [SW102]

+12V

DC JACK

[CN602]

+12V

GND

PAN UNIT

TILT

SENSOR

POWER

DETECT

+3.3V

PWR_DET

BATTERY

BACKUP

BAT101

+3.3V DC-DC

Converter

[IC603]

TILT

MOTOR

DRIVER

+5V DC-DC

Converter

[IC953]

V-Driver

[IC802]

+5V

H/RG

CCDOUT

V,

SUB

CCD_OUT

HD_AFE

CLK Gen  [IC804]

24.5454MHz

PCLK

CS_AFE

+3.3V

RESET

LED_R, LED_G

DC-DC

Converter

[IC801]

+15V

-5.5V

LENS Motor Driver

(Focus/Zoom)

[IC901]

LENS UNIT(Z57)

Zoom

Motor

Focus

Motor

IRIS Unit

F_Enc.

Z_Enc.

IRIS Control

Block

[IC902/904]

DAC

[IC903]

PAN SENSOR

[IC116

]

SCL, SDI

I2C

LVDS  IC

[IC806]

LVDS

THCV214

[IC121]

VD_AFE

MO_LD

DA_LD

LED

[LED901]

Tr

[Q901/902]

TILT

Motor

PAN

Motor

TILT UNIT

LENS Board

IO Board

CPU Board

N_P_DOWN

PAN MOTOR

DRIVER

[IC120]

TILT Board

COMPALATOR

[IC107]

PQUP11499

PQUP11500

40pin

[CN603]

40pin

[CN105]

21pin

[CN102]

20pin[CN103]

21pin

[CN952]

20pin

[CN951]

27pin

[CN954]

4pin

[CN953]

PQUP11486

27pin

[CN804]

VIDEO Board

24M Xtal [X801]

21pin

[CN804]

6.14MHz

1/2 clock  division

[IC807]

3.07MHz

LED_R, LED_G

VD_MOT

VD_MOT

PQUP11487

-0.4V

18pin

[CN902]

21pin

[CN805]

21pin

[CN901]

4pin

 

[CN104]

PQUP11488

DA Comp.

[IC119]

DC-DC

Converter

[IC805]

V,

SUB

CCD

[IC701]

CCD Board

21pin

[CN701]

PQUP11485

AFE/TG  IC

[IC803]

VIDEO

AMP

IC109

LAN TRANS [T601]

VIDEO OUT

Connector

[CN604]