Panasonic SA-XH70GW / SA-XH70EE / SC-XH70EE Service Manual ▷ View online
33
9.4.
Error Code
9.4.1.
Error Code Table 1
Error
Code
F61
The abnormalities
in the Power Amp
output or power
supply
In normal operation, when DCDET2 goes to
L, immediately PCNT is set to L (not normal
POWER OFF sequence), and Error Code
F61 is displayed, without displaying
‘GOODBYE’ scroll on the FL. When happen
error, it memorizes the contents and
displays unusual contents in self-diagnostic
error detection mode.
Press [OPEN/CLOSE]
on main unit for next
error.
F76
Abnormality in the
output voltage of
stabilized power
supply
In normal operation when DCDET1 is
detected L(Low) for two consecutive times,
F76 is displayed on FL for 1 seconds and
after that PCONT will be turned to L (Low).
Press [OPEN/CLOSE]
on main unit for next
error.
Diagnosis
Contents
Contents
Description of error
Automatic FL Display
Remarks
IPOD
OVER
CURRENT
Over current
occurs in Power
Supply for iPod
charging
Disc Region
In normal operation when IPOD_OC is
detected "L" (Low) for two consecutive
times, the message will display on FL once
and Power Supply to iPod shall be cut.
Power off the main unit
and power on again.
F0C1
DVD: Prohibited by the restricted region
code.
F0C3
DVD: Parental lock setting prohibits the
playback of the entire title.
34
9.4.2.
Error Code Table 2
H01
Tray loading error
The tray opening and closing is abnormal.
CLOSE and OPEN of the tray cannot be
carried out properly. Loading motor error,
DV5 LSI IC (IC8001) error.
Press [OPEN/CLOSE] on
main unit for next error.
(OPEN time: OPEN
CLOSE OPEN
H01 at CLOSE: CLOSE
OPEN CLOSE H01)
Press [OPEN/CLOSE] on
main unit for next error.
Press [OPEN/CLOSE] on
main unit for next error.
H03
Traverse motor
error
The traverse is abnormal. (Traverse servo,
DV5 LSI IC (IC8001), TRV motor error.)
U11
Focus servo error
Focus coil, FE signal error. Disc may be
dirty.
(Unfinalized DVD-R is likely
to become U11.)
U702
HDMI/DVI I2C
communication
error
HDMI/DVI HDCP non-HDCP compliance:
Occurs when the equipment is not
compatible with the HDCP receiver.
[HDCP: copyright protection technology.
Digital image signal encryption scheme.]
Press [OPEN/CLOSE] on
main unit for next error.
Press [OPEN/CLOSE] on
main unit for next error.
Press [OPEN/CLOSE] on
main unit for next error.
Press [OPEN/CLOSE] on
main unit for next error.
Press [OPEN/CLOSE] on
main unit for next error.
U703
HDMI/DVI
authentication
error
When authentication (HDCP) with the TV
side fails when connecting it with HDMI/DVI,
it is generated.
U704
HDMI/DVI SRM
error
It is generated at the equipment to which the
TV set is connected with HDMI/DVI.
U705
HDMI/DVI SRM
disk falsification
check error
It is generated at the time of it is time when
illegal the SRM data of the reproducing disk
(verify error), when connecting it with
HDMI/DVI.
F899
The communication
specification
disagreement
between
micro-processor
Unsuitable combination of number of
system com and panel com used.
(Firmware)
Error
Code
Diagnosis
Contents
Contents
Description of error
Automatic FL Display
Remarks
35
9.5.
Sales Demonstration Lock Function
This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function.
“LOCKED” is displayed on the unit, and ordinary operation is disabled.
“LOCKED” is displayed on the unit, and ordinary operation is disabled.
9.5.1.
Setting
• Prohibiting removal of disc
1. Select the DVD/CD function.
2. At POWER ON condition, press and hold down the [
2. At POWER ON condition, press and hold down the [
OPEN/CLOSE
] button and the [- VOL] button on the main unit for at
least three seconds. (The message, “LOCKED” appears when the function is activated.)
Note:
OPEN/CLOSE button is invalid and the main unit displays “LOCKED” while the lock function mode is entered.
• Prohibiting operation of selector and disc
1. Select the DVD/CD function.
2. At POWER ON condition, press and hold down the [
2. At POWER ON condition, press and hold down the [
OPEN/CLOSE
] button and the [VOL +] button on the main unit for at
least three seconds. (The message, “LOCKED” appears when the function is activated.)
Note:
The following buttons are invalid and the main unit displays “LOCKED” while the lock function mode is entered.
9.5.2.
Cancellation
The lock can be cancelled by the same procedure as used in locking. (“UNLOCKED” is displayed on cancellation)
At normal Power ON/OFF the LOCKED condition is not cleared. However, AC Power ON/OFF should clear LOCKED condition.
At normal Power ON/OFF the LOCKED condition is not cleared. However, AC Power ON/OFF should clear LOCKED condition.
Main unit
OPEN/CLOSE
Remote con-
troller unit
AV/INPUT, NUMERIC KEYS 0~9,
, CANCEL, DVD, RADIO, EXT-IN,
, ,
,
, ,
,
, FUNCTIONS,
EXIT, TOP MENU,
, ,
,
, OK, START, MENU, RETURN, PLAY MODE/-REPEAT, CH SELECT, FL DISPLAY
36
9.6.
Firmware Version-Up Information
9.6.1.
Process Flow (1/2)
Collect ROM
Files
(Copy files into
CD-R/RW)
Load disc into
unit
(To update rate)
Step 1
Unzip the firmware update file.
Step 2
Burn below files into root folder of
the CD disc.
Step 3
1. UPDATE.ver
2. XH12_FWXX.img
(Where the XX is the version
number for firmware)
3. mupdate.ver
4. XH70_YY.bin
(Where the YY is the version
number for firmware)
Notes:
1. Software update files =
"mupdate.ver" & "XH70_YY.bin"
2. Firmware update files =
"UPDATE.ver" & "XH12_FWXX.img"
Unzip the firmware update file.
Step 2
Burn below files into root folder of
the CD disc.
Step 3
1. UPDATE.ver
2. XH12_FWXX.img
(Where the XX is the version
number for firmware)
3. mupdate.ver
4. XH70_YY.bin
(Where the YY is the version
number for firmware)
Notes:
1. Software update files =
"mupdate.ver" & "XH70_YY.bin"
2. Firmware update files =
"UPDATE.ver" & "XH12_FWXX.img"
All panel keys and
remote controller keys,
including [ / ] key,
are invalid during CD
Update.
remote controller keys,
including [ / ] key,
are invalid during CD
Update.
Caution:
Make sure the
power supply during CD
update. If the power supply
cable is unplugged during
update stage, CD update
will fail. The DVD model
can't work, and can't be
recovered by CD update
again.
update. If the power supply
cable is unplugged during
update stage, CD update
will fail. The DVD model
can't work, and can't be
recovered by CD update
again.
User can put both files
into the same root
directory. DVD MODEL
will choose the right
ROM files to update
its firmware.
into the same root
directory. DVD MODEL
will choose the right
ROM files to update
its firmware.
FL/ GUI Display
Remarks
Item
Description
Process
1
2
GUI Display 1.1:
Step 1
Power on main unit.
Power on main unit.
Step 2
Change selector to DVD/CD mode
(default is CD/DVD mode)
Change selector to DVD/CD mode
(default is CD/DVD mode)
Step 3
Load in the disc with software/
firmware update data.
Load in the disc with software/
firmware update data.
After disc reading, GUI will
display as:
"GUI Display 1.1:
Are you sure you want to
update the firmware?"
display as:
"GUI Display 1.1:
Are you sure you want to
update the firmware?"
Wait about 15~20 min to finish
update process.
update process.
After disc reading, GUI will
display as:
"GUI Display 1.2:
Updating in progress. Please
wait...Please do not turn off
power during update."
display as:
"GUI Display 1.2:
Updating in progress. Please
wait...Please do not turn off
power during update."
FL will display in the sequence
of " WRITE C", "WRITE D",
" WRITE E", "WRITE F" and
"WRT ROM2" as FL display
1.1~1.5 shown.
of " WRITE C", "WRITE D",
" WRITE E", "WRITE F" and
"WRT ROM2" as FL display
1.1~1.5 shown.
Step 4
Use remote control to select "OK"
button and press remote control
[OK] key.
Use remote control to select "OK"
button and press remote control
[OK] key.
GUI Display 1.2:
FL Display 1.1:
FL Display 1.2:
FL Display 1.3:
FL Display 1.4:
FL Display 1.5:
Display 1:
Click on the first or last page to see other SA-XH70GW / SA-XH70EE / SC-XH70EE service manuals if exist.